background image

3

STEP 1

a.  Lay out the 

Long Bars (CIO)

. Turn the Bars so the holes are on the sides of the Bars as shown below. Slide an 

End Deck 

Plate (CIM)

 (without the angled surface) onto the Bars. Make sure the Bars are fully inserted into the End Deck Plate.

STEP 2

a. Slide the 

Center Deck Plates (CIN)

 (with the angled surfaces) onto the Long Bars as shown, with the angled surfaces facing 

each other.

b.  Slide the other 

End Deck Plate (CIM)

 onto the Bars. Make sure the Bars are fully inserted.

STEP 3

CIM

CIN

CIM

CIM

CIO

CIO

a.  Carefully tip the cart on its side. Secure the 

Center Deck Plates (CIN)

 to the Long Bars by inserting an 

m8 x 53 mm Bolt (CJC)

 

through an 

m8 Flat Washer (CIX)

 and through each hole in the Deck Plates. Slide another Washer over each Bolt and 

secure them with 

m8 Nylock Nuts (CIY)

Repeat for the other side of each Plate.

NOTE: The Center Deck Plates can be secured to either set of holes in the Long Bars, depending on the size of table being stored.  See page 

7 “ADUSTING THE CENTER DECK PLATES FOR 4’ OR 5’ ROUND TABLES” for more information.

The Center Deck Plates must be secured 
before continuing assembly. Failure to secure 
the Plates may result in serious personal 
injury.

WARNING

CIY

CIX

CIX

CJC

CIN

CIO

Содержание 6520








Отзывы: