background image

2

SIGNAL WORDS
Warning

Hazards or unsafe practices 
which COULD result in severe 
personal injury or death if the 
warning is ignored.

The level of risk is indicated by the following signal words:

The safety information in this 
manual is denoted by the safety 
alert symbol:

SAfETy ALERT SyMbOLS AND SIGNAL WORDS

If the warning sticker becomes unreadable, you can re-order it from Customer Service:

1-800-225-3865

SAFETY INFORMATION

WARNING

When using the Wheelbarrow, always heed these 
warnings:
• Do not allow others to ride in Wheelbarrow.  The 
rider can fall out, or the Wheelbarrow can tip over 
causing serious injury.
• Do not exceed the maximum weight of 550 lbs.
• Reduce load if working on hills or slippery 
surfaces.
• Never exceed 10 mph.
• Always begin fi lling the rear of the tub. If a 
heavy item is tossed into the tub in front of the 
axle, the wheelbarrow will quickly tip forward 
causing the handles to jerk upward and possibly 
hit the person fi lling the tub or anyone in the 
handles’ path.
• Since the load is mainly transferred through the 
wheel and not the user, our wheelbarrow is easy 
to overload.

INSTRuCTION N° 1050374

2/11/2009

Copy

Содержание 65027





















Отзывы: