Lifebreath 155 MAX 2019 страница 22 Скачать руководство пользователя

Страница: 22 / 54

lifebreath.com

EPEATER

99-RX02 Repeater

(1)

Green LED

(2)

Red LED

(3)

Power Plug

The wireless repeater is used to extend the range of the 99-DET02 wireless

timers. The repeater plugs directly into a 120V power outlet. The 99-RX02

repeater wirelessly connects to the main control as well as the 99-DET02

wireless timers.

The 99-RX02 repeater should be installed at the halfway point between the 99-

DET02 wireless timer and the main control if the timer is out of range. The LED

will indicate the repeater’s connection strength to the main control per the

table below. Re-adjust the repeater’s position as necessary.

LED Colour

Connection

Action

Solid Green

Good

No further adjustments are required.

Flashing Green

Moderate

The repeater will function properly but shouldn’t be moved further

away from the main control.

Red

Bad

The repeater needs to be moved closer to the main control.

Pairing:

Turn on the main control by pressing the ON/OFF button .

DXPL02 control:

Press the left and right buttons simultaneously on the main control (

and RESET

The screen will go blank, and the wireless symbol will appear flashing on the bottom right of the

display. This indicates that the main control is now in pairing mode.

BC02, BC03 or BC04 control:

Press the left and right buttons simultaneously on the main control

( and or ). The bottom row LED's will begin flashing. This indicates that the main control is

now in pairing mode.

The RX02 Repeater must be powered within 16 in. of the main control for pairing. If an outlet is not

available an extension cord should be used to power the Repeater initially for pairing.

Plug the repeater into the power outlet. The green light will flash after approximately 12 seconds

indicating that the repeater is paired with the main control.

Press the ON/OFF button on the main control to exit pairing mode and the repeater may now be

unplugged and moved to its permanent location.

To pair additional repeaters with the same main control, repeat steps 1 through 5 until all repeaters

have been paired.

Attention

•

The repeaters are to be plugged directly into a 120V power outlet.

Содержание 155 MAX 2019























































Результаты поиска

Содержание 155 MAX 2019

Отзывы:

Похожие инструкции для 155 MAX 2019

Бренды по названию

Популярные бренды

Lifebreath 155 MAX 2019, Руководство по установке

Результаты поиска

Содержание 155 MAX 2019

Отзывы:

Похожие инструкции для 155 MAX 2019

Бренды по названию

Популярные бренды