background image

SPECIFICATIONS

AIRFLOW

1500 cfm (705 L/s) at 1.0”wg ESP.

PERFORMANCE

65% effective at 1500 cfm (705 L/s).

CORES

Six patented aluminum heat recovery cores arranged for

 

efficient 

cross-flow ventilation.

MOTORS

Two single shaft ECM variable speed, 240V, 9.1 A, 1 ph, 1 hp.

(18.2 a total) MCA: 22.8 MOP: 30

BLOWERS

Two direct drive centrifugal blowers, one per airstream.

FILTERS

Two - 20” x 16” x 2” (508 mm x 406 mm x 50 mm) pleated filters in 

each airstream. MERV 6 efficiency 60% @ 4.69 microns.

 

CONNECTION

 

DUCT

 

SIZES

Two 19” x 16” (482 mm x 406 mm) to and from building under cabinet.

 

Two 18” x 17” (457 mm x 431 mm) hoods included on side of cabinet

 

with washable screens.

CABINET

20 gauge powder coated steel 1” (25 mm) thick Elastomeric insulation. 

DRAIN

Two powder coated galvanized steel drain pans with 1/2” (12 mm) 

O.D. drain connections.

MOUNTING

Unit to be set on support brackets hung by threaded rod type

apparatus. Brackets and rod not included.

ELECTRONICS

Integrated microprocessor circuit board. Three (3) independently

adjustable motor speeds.

CONTROL OPTIONS

3

Date:  ___________________________________________ 
Tag:  _____________________Qty:___________________ 
Project:  _________________________________________ 
Engineer: _______________________________________

Contractor:  ______________________________________ 
Supplier:  ________________________________________ 
Quote#:  _________________________________________ 
Submitted by: ____________________________________

DIMENSIONS

 

1500

E

-ECM

 

(

in

 

inches)

Specifications

1500

E

-ECM

DEFROST

Factory set defrost time. Supply motor is shut off while exhaust air 

defrosts core.

WEIGHT

 530 lbs (240 kg) 

SHIPPING WEIGHT 

650 lbs (290 kg)

TIMER OPTIONS

99-

DET01  Lifebreath 20/40/60 Minute Timer

Initiates high speed Ventilation for 20, 40 or 60 minutes

3 wire connection; 20 gauge wire (minimum)

99-

DET02  Lifebreath WIRELESS 20/40/60 Minute Timer

Initiates high speed Ventilation for 20, 40 or 60 minutes

Wirelessly connects to main control for ease of installation

40' approximate range

99-

RX02  Lifebreath WIRELESS Repeater

Used to extend range of 99-DET02 Wireless Timers when

Timers are out of range

Plugs into 120V power outlet and wirelessly connects to main

control and 99-DET02

J

M

STALE AIR
TO OUTSIDE

FRESH AIR

FROM OUTSIDE

STALE AIR

FROM BUILDING

FRESH AIR

TO BUILDING

STALE AIR 

TO OUTSIDE

A

B

C

D

E

F

G

H

I

J

K

L

N

M

EFD inches

20 1.5

17

16.5 41 69.5

20

17

14.5 1.5

20

44 46.5

67

EFD mm

508 38

432 419 1041 1765 508 432

368

39

508 1118 1181 1702

Service Clearance 30”

All units conform

to CSA and UL

standards.

NOTE:

 All 

specifications 

are subject to 

change without 

notice.

INLET END VIEW

SIDE

 VIEW

OUTLET

 END VIEW

WARRANTY

Units carry a 15 year warranty on  the 

H

RV  core 

and a 

2

 year replacement parts warranty.

99-BC02 Lifebreath Ventilation Control

2 speed fan setting (Low/High)

Humidity control through adjustable Dehumidistat

Compatible with 99-DET02 Wireless Timers

3 wire connection; 20 gauge wire (minimum)

99-500 3 Speed Control

3 Speed Fan setting (Low/Medium/High)

4 wire connection; 20 gauge wire (minimum)

99-DH01 Lifebreath Dehumidistat

Humidity control through adjustable Dehumidistat

3 wire connection; 20 gauge wire (minimum)

AIRFLOW PERFORMANCE

1800 

1600

1400 

HIGH SPEED 

1200

1000 

MED SPEED

800

600 

LOW SPEED 

400

200

AIRFLOW   (CFM)

0              0.25        

0.5         0.75        1.0         1.25        1.5

EXTERNAL STATIC PRESSURE  (in. w.g.)

        

1.75        2.0

Содержание 1500E-ECM





























Отзывы: