LIFAN Power USA 2V77F Скачать руководство пользователя страница 34

Страница: 34 / 44

TROUBLESHOOTING

Ⅰ

. Start engine difficultly

ITEM

CAUSE

REMEDY

Check battery connection

Incorrect connection

connect in proper way (P.5)

Check battery

No charge or under charge, corrosion

Check the breaker, charge the battery
or replace it

Check the machine according the following table if the motor runs well

TROUBLE

CAUSE

REMEDY

Normal

compres
sion of
cylinder

good
spark
plug

Abnorm
al fuel
supply
system

Oil flow
is not
smooth
or no oil
flow

There is no enough fuel in fuel
tank or fuel cock is closed.

Fill fuel, open fuel cock.

Air vent in the fuel filler cap is
clogged.

Dredge air vent.

Fuel cock is clogged.

Clean first and then dredge.

Improper or clogged main oil
flow hole.

Readjust or clean, blow to get
through.

Needle valve is not closed
properly or start hole is clogged.

Dismantle needle valve and repair,
clean, blow to get through.

Float is damaged or sticking.

Repair float.

Oil
flow
smoo
thly

Fuel is too filthy or deteriorated.

Replace.

There is water in fuel.

Replace.

Too much fuel in engine.

Drain extra fuel, dry up spark plug
electrodes.

Wrong fuel brand.

Select proper fuel brand
corresponding with the requirements.

Содержание 2V77F













































Результаты поиска

Содержание 2V77F

Отзывы:

Бренды по названию

Популярные бренды

LIFAN Power USA 2V77F, Руководство пользователя

Результаты поиска

Содержание 2V77F

Отзывы:

Бренды по названию

Популярные бренды