manualshive.com logo in svg

LI-COR LI-7810, Инструкция по эксплуатации

Поделиться
Скачать
LI-COR LI-7810 Скачать руководство пользователя страница 68

Section 6. Maintenance

Replacing the purge dry-down chemical

The purge chemical, consisting of silica gel beads, is contained in a non-porous tube.
The instrument will pump air through the purge tube during the power-off routine
to ensure that the optics are free of water vapor while the instrument is in storage.
You may need to replace the chemical periodically. The silica gel pellets are orange
when new and green when saturated.

Warning:

May cause irritation. MAY CAUSE SKIN IRRITATION. MAY CAUSE

RESPIRATORY TRACT IRRITATION. MAY CAUSE PAIN, NAUSEA, VOMITING AND
DIARRHEA. May result in coughing and/or sore throat. PROLONGED OR REPEATED
EXPOSURE TO DUST MAY CAUSE PULMONARY PROBLEMS. INGESTION MAY CAUSE
GASTRIC DISTURBANCES.

Advertissment:

Peut causer une irritation. PEUT CAUSER UNE IRRITATION DE LA

PEAU. PEUT CAUSER UNE IRRITATION DE LA VOIE RESPIRATOIRE. PEUT CAUSER
DOULEURS, NAUSÉE, VOMISSEMENTS ET DIARRHÉE. Peut entraîner une toux et / ou
un mal de gorge. L’EXPOSITION PROLONGÉE OU RÉPÉTÉE A LA POUSSIÈRE PEUT
CAUSSER DES PROBLÈMES PULMONAIRES. L’INGESTION PEUT CAUSER DES
PERTURBATIONS GASTRIQUES.

To replace the purge chemical:

1

Power off the instrument.

2

Open the lid and locate the purge chemical column.

3

Disconnect the quick-connect fittings from the column inlet and outlet.

6-6

LI-7810 CH₄/CO₂/H₂O Trace Gas Analyzer

Содержание LI-7810



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды