LI-COR LI-7810 Скачать руководство пользователя страница 51

Страница: 51 / 98

Operating information

The bottom portion of the window provides more details about the instrument oper-
ating history and status.

Pump Operating Hours

is the number of hours that the pump has operated.

Thermal Enclosure Temp

is the temperature of components inside the foam insu-

lating enclosure. If red, the instrument is either too hot and unable to regulate
the enclosure temperature, or too cold and in a warmup state. Normally this is
between 51.5 °C and 57.5 °C.

Cavity Temperature

is the optical bench temperature. If red, the instrument is

either too hot and unable to regulate the cavity temperature, or too cold and in a
warmup state. Normally this is between 52 °C and 58 °C.

Laser Temperature

is the temperature of the diode laser. If red, the instrument is

unable to regulate the laser temperature.

Laser Temp. Shift

is the shift in the laser center wavelength from the factory cal-

ibration.

Ring Down Time

is a parameter indicating cavity resonance.

Device Uptime

shows the number of hours that the instrument has been

powered on.

On/Off cycles

is the number of times the instrument has been powered on.

Section 4. Software overview

4-13

Operating information

Содержание LI-7810



































































































Результаты поиска

Содержание LI-7810

Отзывы:

Бренды по названию

Популярные бренды

LI-COR LI-7810, Инструкция по эксплуатации

Результаты поиска

Содержание LI-7810

Отзывы:

Бренды по названию

Популярные бренды