LG STB-3000 страница 4 Скачать руководство пользователя

Страница: 4 / 86

206-4272

(Continued from previous page)

22. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the

product, follow the precautions below.

An outdoor antenna system should not be located in the

vicinity of overhead power lines or other electric light or power

circuits or where it can come into contact with such power

lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded so as to provide

some protection against voltage surges and built-up static

charges.

Article 810 of the National Electrical Code (NEC) in the U.S.A.

provides information with respect to proper grounding of the

mast and supporting structure, grounding of the lead-in wire

to an antenna-discharge unit, size of grounding conductors,

location of antenna-discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

Antenna Grounding According to NEC, ANSI/NFPA 70

23. Cleaning

When cleaning, unplug the power cord and wipe gently with

a soft cloth to prevent scratching. Do not spray water or other

liquids directly on the STB as electric shock may occur. Do not

clean with chemicals such as alcohol, thinners or benzene.

24. Transporting Product

Make sure the STB is turned Off and unplugged and that

all cables have been removed. Do not press against or put

stress on the STB.

25. Ventilation

Install the STB where there is proper ventilation. Do not

install in a confined space such as a bookcase. Do not cover

the STB with cloth or other materials (e.g., plastic) while it is

plugged in. Do not install in excessively dusty places.

26.

Do not touch the ventilation openings, as they may become

hot while the STB is operating.

27.

If you smell smoke or other odors coming from the STB or

hear strange sounds, unplug the power cord, and contact an

authorized service center.

28.

Keep the product away from direct sunlight.

IMPORTANT SAFETY INSTRUCTIONS

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Содержание STB-3000























































































Результаты поиска

Содержание STB-3000

Отзывы:

Похожие инструкции для STB-3000

Бренды по названию

Популярные бренды

LG STB-3000, Руководство по установке

Результаты поиска

Содержание STB-3000

Отзывы:

Похожие инструкции для STB-3000

Бренды по названию

Популярные бренды