LG STB-2000 Скачать руководство пользователя

Страница: 7 / 86

206-4256

STB-2000 Cabling Connections

This section describes how to connect the STB-2000 to a compatible commercial display panel (LG

Hospitality TV, LG Public Display TV, LG Commercial Monitor, or commercial non-LG TV with MTI support).

Connect the STB to the Display Panel

The following procedure only describes those connections that are essential for STB functionality. See

Reference section, “STB-2000 Jack Panels,” for further information on the additional jack panel ports and

connectors.

Note:

An LG Installer Remote (not supplied) is required to complete this procedure, as well as STB/display

panel configuration procedures in this document. If you are using an LG display panel, a standard LG

Installer Remote should be sufficient. However, if you are not using an LG display panel and/or if you wish

to take advantage of the STB’s multi-code feature, LG’s STB-dedicated Installer Remote will be required.

See Reference sections, “Installer Remote Typical Key Functions” and “STB Installer Remote,” for further

information.
1. Turn ON the display panel. Before you connect the STB to the display panel, the display panel should

be in a known state. That is, the display panel should be either in a factory default state or custom

configured (in its default mode) with selected settings, for example, the aspect ratio, that you wish to

use in conjunction with the STB.
When you are ready to proceed, leave the display panel turned ON, and then continue with step 2.

2. Refer to the STB-2000 Cabling diagram on the next page, and complete the following connections:

a) Make the appropriate Display Control connection between the STB-2000 and the display panel.

• For LG Hospitality TVs: Use the MPI/MTI cable provided to connect DISPLAY CONTROL 2 on the

STB-2000 front jack panel to the MPI port on the rear jack panel of the display.

• For LG Public Display TVs or LG Commercial Monitors: Use the TLM cable provided to connect

DISPLAY CONTROL 1 on the STB-2000 rear jack panel to the RS-232 CONTROL

connector on the rear jack panel of the display.

• For commercial non-LG TVs: Use the MPI/MTI cable provided to connect DISPLAY CONTROL 2 on

the STB-2000 front jack panel to the MTI (typically labeled “DATA”) port on the rear jack panel of the

display.

b) Use the HDMI cable provided to connect HDMI OUT on the STB-2000 rear jack panel to the HDMI1

input connector on the rear jack panel of the display.

c) Connect a 75 ohm coaxial wire from the Antenna/CATV wall jack to ANTENNA/CABLE IN on the

STB-2000 rear jack panel.

d) Insert the DC power plug of the AC/DC power adapter provided into the POWER connector on the

rear jack panel of the STB-2000, and then plug the AC/DC adapter into a standard 120V 60 Hz AC

power outlet.
Once power is applied to the STB-2000, the LED on the STB’s front jack panel will light steadily,

indicating that the STB is in standby mode. Also, the display panel will be turned OFF by the STB as

soon as the STB is powered and establishes display control communication with the display.

Note:

Once display control communication is established between the STB-2000 and the display

panel, the STB-2000 will be in control of the display panel, and certain resident panel functions, like

panel buttons, will no longer operate.

3. Use the Installer Remote to turn ON the STB/display panel.

(Continued on next page)

Содержание STB-2000























































































Результаты поиска

Содержание STB-2000

Отзывы:

Похожие инструкции для STB-2000

Бренды по названию

Популярные бренды

LG STB-2000, Руководство по установке

Результаты поиска

Содержание STB-2000

Отзывы:

Похожие инструкции для STB-2000

Бренды по названию

Популярные бренды