LG MS-191MC Скачать руководство пользователя

Страница: 16 / 17

5-15

CONDITION

CHECK

RESULT

CAUSE

REMEDY

No microwave
oscillation.

No continuity.

Continuity.

Abnormal

Defective high
voltage
transformer.

Replace high
voltage
transformer.

Normal

Defective PCB
assembly.

Replace PCB
assembly.

Disconnect the
wire leads from
relay 2 and
check continuity
of relay 2.
(Operate the unit)

Check high vol-
tage transformer.

Abnormal

Defective circuit
protector.

Replace circuit
protector.

Normal

Check circuit
protector.

Abnormal

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Normal

Check high vol-
tage capacitor.

Abnormal

Defective high
voltage diode.

Replace high
voltage diode.

Normal

Check high vol-
tage diode.

Abnormal

Defective
magnetron.

Replace
magnetron.

Check
magnetron.

(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run.

(Display operates properly)

Содержание MS-191MC


















Результаты поиска

Содержание MS-191MC

Отзывы:

Похожие инструкции для MS-191MC

Бренды по названию

Популярные бренды

LG MS-191MC, Руководство по обслуживанию

Результаты поиска

Содержание MS-191MC

Отзывы:

Похожие инструкции для MS-191MC

Бренды по названию

Популярные бренды