LG MH2044DB страница 25 Скачать руководство пользователя

Страница: 25 / 36

5-15

CONDITION

CHECK

RESULT

CAUSE

REMEDY

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1.Setting time does

not count down
when touching
START pad.

No continuity.

Continuity.

Defective
secondary switch.

Replace
secondary switch.

Check continuity
of secondary
switch (with
door closed).

Check the con-
nection between
connector and
P.C.B assembly.

2. Fan motor or

oven lamp
do not turn
on.

Abnormal.

Defective fan
motor.

Replace fan
motor.

Check fan motor.

Abnormal.

Defective oven
lamp.

Replace oven
lamp.

Check oven lamp.

Normal.

No continuity.

Continuity.

Defective P.C.B
assembly.

Replace P.C.B
assembly.

Loose connection.

Connection then
tightly.

Output is low.

Lower than 90% of
rating voltage.

Normal.

Decrease in power
source voltage
with load.

Suggest customer
contact local
electric power
utility co. or
qualified
electrician.

Check the
power source
voltage.

Disconnect the
wire leads from
relay 2 and check
on and off time
with multitester.

Abnormal.

Normal.

Abnormal.

Defective
magnetron.

Replace
magnetron.

Defective P.C.B
assembly.

Replace P.C.B
assembly.

Measure the
output power.

(TROUBLE 3) Display shows all figures set, but oven does not start cooking while

desired program times are set and START pad is touched.

(TROUBLE 4) Oven seems to be operation but little heat is produced in oven load.

NOTE: Simple test of power output-conducted by heating one liter water for one min. if available.

Содержание MH2044DB





































Результаты поиска

Содержание MH2044DB

Отзывы:

Похожие инструкции для MH2044DB

Бренды по названию

Популярные бренды

LG MH2044DB, Руководство по обслуживанию

Результаты поиска

Содержание MH2044DB

Отзывы:

Похожие инструкции для MH2044DB

Бренды по названию

Популярные бренды