background image

14  Bass

 (Command: k s)

(Depending on model)

 

To adjust bass. You can also adjust Bass in the 

audio settings.

Transmission

[k][s][ ][

Set ID

][ ][

Data

][Cr]

Data

 Min : 00 to Max : 64

Ack

[s][ ][

Set ID

][ ][

OK

/

NG

][

Data

][x]

15 

Balance

 (Command: k t)

 

To adjust balance. You can also adjust balance in 

the audio settings.

Transmission

[k][t][ ][

Set ID

][ ][

Data

][Cr]

Data

 Min : 00 to Max : 64

Ack

[t][ ][

Set ID

][ ][

OK

/

NG

][

Data

][x]

16 

Color Temperature

 (Command: x u)

 

To adjust colour temperature. You can also 

adjust color temperature in the picture settings.

Transmission

[x][u][ ][

Set ID

][ ][

Data

][Cr]

Data

 Min : 00 to Max : 64

Ack

[u][ ][

Set ID

][ ][

OK

/

NG

][

Data

][x]

17 

Equalizer

 (Command : j v)

 

Adjust EQ of the set.

Transmission

[j][v][ ][

Set ID

][ ][

Data

][Cr]

0

0

0

0

0

0

0

0

MSB

Frequency

Data

LSB

7

6

5

Frequency

4

3

2

1

0

Step

0

0

0

1st Band

0

0

0

0

0

0(decimal)

0

0

1

2nd Band

0

0

0

0

1

1(decimal)

0

1

0

3rd Band

...

...

...

...

...

...

0

1

1

4th Band

1

0

0

1

1

19(decimal)

1

0

0

5th Band

1

0

1

0

0

20(decimal)

Ack

[v][ ][

Set ID

][ ][

OK

/

NG

][

Data

][x]

* It depends on model, and can adjust when sound 

mode is EQ adjustable value.

18  Energy Saving

 (Command: j q)

(Depending on model)

 

To reduce the power consumption of the TV. You 

can also adjust energy saving in picture settings.

Transmission

[j][q][ ][

Set ID

][ ][

Data

][Cr]

Data

 00 : 

Off

Data

 01 : 

Minimum

Data

 02 : 

Medium

Data

 03 : 

Maximum

Data

 04 : 

Auto

Data

 05 : 

Screen off

Ack

[q][ ][

Set ID

][ ][

OK

/

NG

][

Data

][x]

19  Tune Command

 (Command: m a)

* This command may work differently depending 

on model and signal.

* For Europe, Mid-East, Colombia, Asia except 

South Korea and Japan Model

 

Select channel to following physical number.

Transmission

[m][a][ ][

Set ID

][ ][

Data

 00][ ][

Data

 01]

[ ][

Data

 02][Cr]

 

Analog Antenna/Cable

[

Data

 00][

Data

 01] Channel Data

Data

 00 : High byte channel data

Data

 01 : Low byte channel data

 

- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)

Data

 02 : Input Source (Analog)

 

- 00 : Antenna TV (ATV)

 

- 80 : Cable TV (CATV)

44

ENGLISH

Содержание LT340C0U Series

















































Отзывы: