LG LS-J0762NM Скачать руководство пользователя страница 61

Страница: 61 / 82

-61-

■

The problem of missing the connector (INDOOR MAIN PCB ASSY)

■

The problem of missing the connector (OUTDOOR MAIN PCB ASSY)

Connectors

CN-AC/DC

CN-FAN

CN-DISP1

CN-DISP2

CN-TH

CN-U/D

Condition

OPEN

OPEN/SHORT

OPEN

• Malfunctions all indoor & outdoor unit.
• Malfunctions remocon, force, test operation mode.

• Malfunctions remote contoller.
• Don't operate the power display module.

• Don't operate the power display module.

• The operation LED blinks twice.
• Enable to receive remote singnal.

• Malfunctions UP/DOWN step motor.
• Don't operate louver.

• Malfunctions indoor fan motor.

Problem (error mode)

Connectors

Condition

OPEN

• Stop compressor.

• Malfunctions 4-WAY valve.

• Malfunctions fan

Problem (error mode)

CN-TH

CN-UVW

CN-4 WAY

CN-FAN

CN-COMP

OPEN/SHORT

• The operation LED blinks twice.
• The LED01M blinks twice.

• The LED01M blinks 10 times.
• Continue Comp. operation.

(when the discharge pipe TH opens)

• Stop Comp. operation

(when the discharge pipe TH shorts)

Содержание LS-J0762NM


















































































Результаты поиска

Содержание LS-J0762NM

Отзывы:

LG LS-J0762NM, Руководство по обслуживанию, Страница: 61 / 82

Результаты поиска

Содержание LS-J0762NM

Отзывы: