manualshive.com logo in svg

LG LS-J0762NM, Руководство по обслуживанию, Страница: 23 / 82

Поделиться
Скачать
LG LS-J0762NM Скачать руководство пользователя страница 23

18. Portection from overheating of power module

• If the temperature of the heat sink TH. reaches over Toff, the Compressor stop instantly.
• It will be limited the compressor operating frequency according to the heat sink TH.(refer to below FIG.)
• It will be blink 4 times, when the thermistor is open or short, also the temperature is over Toff.

19. Portection from overheating of compressor

• If the temperature of the discharge pipe of compressor reaches over 130°C or below -30°C the compressor

stop instantly.

• It will be limited the compressor operating frequency according to the compressor dome TH.(Refer to below

Fig.)

• Temperature range by COMP SPEC varies by 10°C.

-23-

Comp. off

Comp. free

Fc-1

Fc-2

Target frequency

Toff (95

°

C)

Ton + 3

°

C (88

°

C)

Ton + 6

°

C (91

°

C)

Ton (85

°

C)

130

°

C

118

°

C

111

°

C

108

°

C

-13

°

C

-30

°

C

101

°

C

93

°

C

Fhmin

OFF

OFF

0Hz

Fc-2

Fc-1

Setting frequency

[The control graph from heat–sink TH]

Содержание LS-J0762NM



















































































Отзывы:

Нет отзывов