LG LMNC126LRL0 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 22

background image

Installation Manual 15

ENGLISH

Connecting the Cable between Indoor Unit and Outdoor Unit

Connecting the Cable between Indoor Unit and Outdoor Unit

Connect the cable to the indoor unit by connecting the wires to the terminals on the control
board individually according to the outdoor unit connection. (Ensure that the color of the wires
of the outdoor unit and the terminal No. are the same as those of the indoor unit.)
The earth wire should be longer than the common wires.
The circuit diagram is not subject to change without notice.
When installing, refer to the circuit diagram behind the panel front of Indoor Unit.
• When installing, refer to the circuit diagram behind the panel front of Indoor Unit.
• When installing, refer to the wiring diagram on the Control Cover Inside Outdoor Unit.

Connect the cable to the Indoor unit.

CAUTION:
• The circuit diagram is not subject to change without notice.
• Be sure to connect wires according to the wiring diagram.
• Connect the wires firmly, so that not to be pulled out easily.
• Connect the wires according to color codes by referring the wiring diagram.

CAUTION: Provide a circuit
breaker between power source
and the unit as shown below.

CAUTION: The power cord connected to the outdoor unit should comply with
the following specifications (Cable type approved by HAR or SAA).

The power connecting cable connected to the indoor and outdoor unit
should comply with the following specifications (Type "B" approved by HAR
or SAA).

Air

Conditioner

Main power source

Circuit Breaker
Use a circuit breaker
or time delay fuse.

GN/YL

20mm

48k

60k

8.5

8.5

Cable Type

H05RN-F

H05RN-F

NORMAL CROSS

SECTIONAL AREA

Grade

(mm

2

)

NORMAL
CROSS-SECTIONAL
AREA 0.75mm

2

ø

7.5mm

GN/YL

20mm

«
...
13
14
15
16
17
...
»

Содержание LMNC126LRL0























Отзывы:

Нет отзывов

Похожие инструкции для LMNC126LRL0

Duct Type Series

Бренд: Samsung Страницы: 40

SYSVRF JOINT OUT 02 HP

Бренд: SystemAir Страницы: 2

Бренд: S.S.Green Страницы: 11

Бренд: Nortek Страницы: 16

Бренд: Daewoo Страницы: 96

Бренд: ICP Страницы: 14

Бренд: Daikin Страницы: 26

Бренд: Kaysun Страницы: 16

Бренд: AERMEC Страницы: 12

Бренд: Impecca Страницы: 40

activair SAC16870N

Бренд: Swann Страницы: 20

Бренд: Daikin Страницы: 16

Бренд: Rowenta Страницы: 44

Бренд: GVA Страницы: 6

Бренд: Aeroex Страницы: 12

Бренд: Prem-I-Air Страницы: 12

Бренд: Daitsu Страницы: 56

Бренд: HiRef Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды