LG LG A1C-V5 Series Скачать руководство пользователя страница 92

Страница: 92 / 108

Electronics

AC Module System Installation Manual

Rev. 1.0

Measure point

Single Phase 240V(RMS)

Single Phase 208V(RMS)

Three Phase 208V(RMS) Merge, Split Type

Expected

Range

Measured

Expected

Range

Measured

Expected

Range

Measured

L1 – N

60Hz

59.3~60.5

60Hz

59.3~60.5

60Hz

59.3~60.5

L2 – N

60Hz

59.3~60.5

60Hz

59.3~60.5

60Hz

59.3~60.5

L3 – N

60Hz

59.3~60.5

L1 – L2

60Hz

59.3~60.5

60Hz

59.3~60.5

60Hz

59.3~60.5

L2 – L3

60Hz

59.3~60.5

L3 – L1

60Hz

59.3~60.5

5-8 Grid Frequency Measurement

Measure grid frequency of the utility at the distribution panel and AC junction box using a voltmeter. Fill

out the below table. If the measured frequency is out of the range which is specified in each table, then

ask the local electricity provider about voltage frequency instability. After the work, please follow 3-15

Energize the installed AC module system to restart the system.

At distribution panel

At AC junction box

Measure point

Single Phase 240V(RMS)

Single Phase 208V(RMS)

Three Phase 208V(RMS) Merge, Split Type

Expected

Range

Measured

Expected

Range

Measured

Expected

Range

Measured

L1 – N

60Hz

59.3~60.5

60Hz

59.3~60.5

60Hz

59.3~60.5

L2 – N

60Hz

59.3~60.5

60Hz

59.3~60.5

60Hz

59.3~60.5

L3 – N

60Hz

59.3~60.5

L1 – L2

60Hz

59.3~60.5

60Hz

59.3~60.5

60Hz

59.3~60.5

L2 – L3

60Hz

59.3~60.5

L3 – L1

60Hz

59.3~60.5

AC junction box

An array of AC modules

Frequency

measure

Meter

•

Plan the installation work in moderate weather. There is a risk of electric shock when it is raining snowing.

•

To prevent the risk of accidents, use proper PPE (Personal Protective Equipment) including helmets, eye

protection and gloves at all times.

•

If installation location is high above ground, make sure to use Fall Protection System during the installation.

•

For safety, only qualified personnel should undertake the work.

1. Turn off the circuit

breaker first.

2. Leave the transition

cable disconnected.

Meter

N L1 L2

Meter

General Wiring

Distribution panel

Содержание LG A1C-V5 Series












































































































Результаты поиска

Содержание LG A1C-V5 Series

Отзывы:

LG LG A1C-V5 Series, Руководство по установке, Страница: 92 / 108

Результаты поиска

Содержание LG A1C-V5 Series

Отзывы: