manualshive.com logo in svg

LG LG A1C-V5 Series, Руководство по установке, Страница: 22 / 108

Поделиться
Скачать
LG LG A1C-V5 Series Скачать руководство пользователя страница 22

Electronics

AC Module System Installation Manual

Copyright © 2020 LG Electronics.

All Rights Reserved.

22

Rev.  1.0

3-8 Coupling AC cable Connectors

Before  pairing  AC  cable  connectors,  familiarize  yourself  with  the  following  descriptions  specifically 

explaining how to handle AC cable connectors and accessories.

•  Insert the AC cable female connector into the AC cable male connector horizontally. If you insert at the wrong  

angle, the connector can be damaged.

•  When the temperature is warm and you are about to engage two connectors, you might not hear two clicks. In that 

case, engage connectors until there is no space (no gap) between connectors.

•  Insert the connector fully into the end of the other connector until you hear two clicks.
•  When the connectors are correctly connected, there should be no space between the end of a male connector and 

the end of a female connector.

•  Do not let cable be pulled too tight or hang too loose. Internal conductor may break.
•  Do not allow any liquid inside to prevent danger of electric shock.
•  Do not use damaged cables.
•  Do not cut or transform AC cables for use.
•  Frequent disassembly or connection may damage connectors.
• 

The size of the cables are in accordance with NEC2014. (For the size, refer to Chapter 9. Product Specification)

•  For information about accessories, refer to Chapter 8. Accessories.

• 

AC cable information can be found in Chapter 

8 AC Module Accessories

.

AC cable connector insertion

•  AC cable connectors can be easily paired to connectors in the right direction.
• 

Before pairing two AC cable connectors, identify the locations of ‘Fool-proof system’ on each AC cable connector.

• 

Inserting the AC cable female connector into the AC cable male connector is only possible when ‘Fool-proof 

System’ is properly matched.

• 

Use fool-proof system 1 or 2 as per your convenience.

Fool-proof System 1

Fool-proof System 2

F

M

No gap

A gap

Содержание LG A1C-V5 Series













































































































Отзывы:

Нет отзывов