LG LG A1C-A5 Series Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 107

background image

AC Module System Installation Manual

Rev. 1.0

105

Appendix 2 – Module Installation & Load Guide

Mechanical Installation : LGXXXA1C-A5

Fig. 1 Mounting Type

Fig. 2 Clamping Type

①

: 200mm(7.9 in)

②

: 300mm(11.8 in)

Front : 6000Pa(125psf)

Rear : 5400Pa(113psf)

A : 270mm(10.6 in)
B : 400mm(15.7 in)

Front : 6000Pa(125psf)

Rear : 5400Pa(113psf)

Fig. 3 Clamping Type

Fig. 4 Clamping Type

A : 270mm(10.6 in)
B : 400mm(15.7 in)

Front : 4300Pa(125psf)

Rear : 4300Pa(113psf)

A : 120mm(4.7 in)

Front : 1800Pa(37.5psf)

Rear : 1800Pa(37.5psf)

B : 200mm(7.9 in)

Front : 2850Pa(50psf)

Rear : 2850Pa(50psf)

Fig. 5 Clamping Type

Fig. 6 Clamping Type

*4 point installation is allowed in the following cases.:
1. Slope roof: If module is installed parallel to the rooftop.
2. Flat roof: If installed with an additional stand such as wind shield or deflector.

A : 200mm(7.9 in)

B : 400mm(15.7 in)

Front : 6000Pa(125psf)

Rear : 5400Pa(113psf)

A : 120mm

(4.7 in)

*4point(

①

)

Front : 1800Pa(37.5psf)

Rear : 1800Pa(37.5psf)

C : 120mm(4.7 in)

Front : 3200Pa(67psf)

Rear : 1800Pa(37.5psf)

A : 120mm

B : 843

±

100mm

(33.2

±

3.9 in)

6point

(

①

+

②

)

Front : 6000Pa(125psf)

Rear : 5400Pa(113psf)

Note) All mechanical installation method(Fig. 1 to Fig. 6) in this appendix were not tested by UL.
(UL 1703, ULC 1703) It is evaluated by LG internal test.

Copyright © 2017 LG Electronics.

All Rights Reserved.

②

②

②

②

«
...
103
104
105
106
107
»

Содержание LG A1C-A5 Series












































































































Отзывы:

Нет отзывов

Похожие инструкции для LG A1C-A5 Series

Бренд: YOKOGAWA Страницы: 58

Бренд: TANDBERG Страницы: 384

E5714 DSNG Voyager

Бренд: TANDBERG Страницы: 314

Бренд: Wacker Neuson Страницы: 22

Бренд: TTI Страницы: 7

Бренд: Lambda Страницы: 47

Бренд: Trycom Technology Страницы: 20

Бренд: Hama Страницы: 8

Бренд: QUAD Страницы: 38

Бренд: Q CELLS Страницы: 11

Бренд: Lika Страницы: 104

Energier Pro CF2060L

Бренд: TBB Страницы: 60

Бренд: Ediseja 21 Страницы: 22

Бренд: Speeka Страницы: 18

Бренд: Diehl Страницы: 28

Бренд: Stanley Страницы: 7

Бренд: Miteq Страницы: 55

Power WHISPERWATT DCA-45SSIU2

Бренд: MULTIQUIP Страницы: 160

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды