LG HCED3015D Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 35

background image

-12-

PLANNING THE INSTALLATION

ELECTRICAL

For personal safety, remove house fuse or open

circuit breaker before beginning installation. Do not

use extension cord or adapter plug with this

appliance.

Follow national electrical codes or prevailing

local codes and ordinances.
Electrical Supply:
This appliance requires a 120V 60Hz electrical

supply, and connected to an individual, properly

grounded branch circuit, protected by a 15 or 20

ampere circuit breaker or time delay fuse. Wiring

must be 2 wire w/ ground. Please also refer Electrical

Diagram labeled on product.

Cable Lock:
A cable locking connector (not supplied) might also

be required by local codes. Check with local

requirements and codes, purchase and install

appropriate connector if necessary.

Cable Lock

WARNING

All Electrical work must by performed by

qualified electrician or person with similar

technical know how and background.

WARNING

Electrical wiring must be done by a qualified

person(s) in accordance with all applicable

codes and standards. This range hood must

be properly grounded. Turn off electrical

power at service entrance before wiring.

«
...
10
11
12
13
14
...
»

Содержание HCED3015D




































Отзывы:

Нет отзывов

Похожие инструкции для HCED3015D

Бренд: Faber Страницы: 16

30" (76.2 cm) Cooktop

Бренд: Jenn-Air Страницы: 32

Бренд: S&P Страницы: 74

Бренд: Otto Страницы: 109

Gorenje S3 WHT641ST

Бренд: S+ARCK Страницы: 180

Verona Island ZVN-E42AG

Бренд: Zephyr Страницы: 54

IN2642SQB-1200-1

Бренд: KOBE Страницы: 24

Nova Trend E9004390

Бренд: Cylinda Страницы: 34

Бренд: FALMEC Страницы: 60

Design Plane 90 Inox

Бренд: FALMEC Страницы: 59

Бренд: Vent-Axia Страницы: 8

Бренд: Faber Страницы: 15

Бренд: Faber Страницы: 36

Бренд: FALMEC Страницы: 24

Бренд: Inalto Страницы: 2

Бренд: Gaggenau Страницы: 12

Бренд: myappliances Страницы: 12

Бренд: EF Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды