28
206-4232
104 - START MINOR CHANNEL
Sets Minor Start Channel number at power up. 0 = NTSC. If not
0, number selected is the digital channel’s Minor Start Channel
number.
Note:
This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 0 or 255.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power off. Set to 0 to
retain default aspect ratio with power off. See item 096 DEF. ASP.
RATIO above.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for Normal. Set to 1 for Blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal. Set to 1 to restore the factory default settings
of all Installer Menu items.
Caution:
If set to 1, this will restore the factory defaults
and clear the channel lineup, including any assigned
channel icons and custom text labels.
Note:
See also Reference section, “Restoring Factory Defaults on
the TV(s),” for further information.
118 - POWER SAVINGS
Default set to 3—the power circuitry for both the embedded
b
-LAN
module and the GAME CONTROL/MPI port is only powered when
the TV is turned ON. When the TV is turned OFF, the embedded
b
-LAN and the GAME CONTROL/MPI port are not powered.
Note that the TV must be turned ON in order to communicate with
the embedded
b
-LAN module for configuration and control when
POWER SAVINGS is set to 3. If POWER SAVINGS is set to 1,
the
b
-LAN module is always powered.
Similarly, if MPI communication is required for external MPI
control, POWER SAVINGS should be set to 1 so that the GAME
CONTROL/MPI port circuitry is always powered.
Note:
See Reference section, “
b
-LAN Setup & Overview,” for
further information.
Caution: POWER SAVINGS should NEVER be set to 7.
This setting is intended for factory use only.
119 - DATA CHANNEL
Set to 0 to disable. Set from 1 to 135 to match the RF channel
number that will be used by the Pro:Centric server as its data
channel. *
For TVs in Pass-through Mode or FTG Mode via CPU, if this item
is left at its default value (255), the TV’s Data Channel Auto Search
feature will be enabled (see additional information below).
Note:
The Data Channel Auto Search feature is not available
when the TV’s EBL is in FTG Mode. If the DATA CHANNEL value
is 255 when the TV is configured for FTG Mode via EBL, DATA
CHANNEL is defaulted to 0.
Data Channel Auto Search feature: When this item is set to 255
(default), once every 24 hours, the TV will initiate a search of 10
predefined channels (10, 20, 30, ... 100) and then, if necessary,
perform a complete search of the RF channels (1 to 135) in an
attempt to find the RF channel used by the Pro:Centric server as
its data channel. If the Pro:Centric RF channel is found, the DATA
CHANNEL value will be changed from 255 to match the server’s
RF channel number. The time at which the Auto Search occurs
depends on the setting of item 121 P:C RF WAKE HR. See item
121 description for further information.
Note:
Pro:Centric updates are downloaded from the Pro:Centric
server to the TV when the TV is turned OFF. While Pro:Centric
updates are in progress, it is not possible to turn ON the TV.
121 - P:C RF WAKE HR
Set the Wake On RF hour from 0 to 23. This item uses the
24-hour clock format. The value “128” is displayed as “OFF.”
Directly entering 128 turns the Wake On RF feature OFF.
The Wake On RF feature uses a timer, based on the settings
of this item and item 122 P:C RF WAKE MN, to wake the TV to
check for and, if applicable, download updates.
If Wake On RF is OFF, the time at which a Data Channel Auto
Search (item 119 set to 255) occurs is determined as follows: The
TV will initiate the search at 2:00 PM (if the TV clock is set) or at 14
hours of elapsed time from when AC power was applied (if the TV
clock is not set). If the TV display is ON when the Auto Search is
due to occur, the Auto Search will take place the next time the TV is
turned OFF.
Note:
This item is not available in the Installer Menu when item
119 DATA CHANNEL is set to 0.
Note:
The TV clock must be set in order for a Wake On RF event
to occur at the precise time of day in accordance with item 121
and 122 settings.
122 - P:C RF WAKE MN
Set the Wake On RF minute from 0 to 59. See also description for
item 121 P:C RF WAKE HR above.
Note:
This item is not available in the Installer Menu unless item
121 P:C RF WAKE HR is set from 0 to 23.
Note:
The TV clock must be set in order for a Wake On RF event
to occur at the precise time of day in accordance with item 121
and item 122 settings.
Installer Menu (Cont.)
*
PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.
