manualshive.com logo in svg

LG AT-C186PLE0, Руководство по установке, Страница: 23 / 28

Поделиться
Скачать
LG AT-C186PLE0 Скачать руководство пользователя страница 23

Installation

Installer Setting - Installer Setting Code Table

M ode Override
This Function is only for Non-Auto Changeover H/P model. 

Ceiling Height S election
Indoor unit connected to wired remote controller operate as wired remote controller setting.

Group Control
This function is only for group control. Please don’t set this function in case of non-group
control.
After setting Group Control of the product, turn off the power then turn it back on after 1
minute. 

Auxiliary heater
This function is only applied to models with Auxiliary Heater function being activated.

Installer Setting Code Table

No.

Function

Function Code

S etting Value

R emote Controller LCD

0

Mode Override

0

0 : Set to Master

1 : Set to Slave

1

Ceiling Height

Selection

1

1 : Standard

2 : Low

3 : High

4 : Super High

2

Group Control

2

0 : Set to Master

1 : Set to Slave

2 : Check Master/Slave

Auxiliary heater

2

3 : Set to Auxiliary heater

4 : Cancel Auxiliary heater

5 :  Check Auxiliary heater Installation

Installation Manual 

23

Содержание AT-C186PLE0





























Отзывы:

Нет отзывов