manualshive.com logo in svg

LG ABNQ18GHLA0, Руководство по обслуживанию, Страница: 57 / 100

Поделиться
Скачать
LG ABNQ18GHLA0 Скачать руководство пользователя страница 57

- 57 -

Copyright ©2013 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

Part 4  Trouble Shooting 

Table 1

Table 1

Model.

Resistance(

Ω

) at 20°C

AUUQ18GH1/AUUQ21GH1/AUUQ24GH1(ATUQ18GPLE3/ ATUQ21GPLE3/ ATUQ24GNLE3)
(AVUQ18GJLA0/ AVUQ21GJLA0 / AVUQ24GJLA0)
(ABUQ18GHLA0/ ABUQ21GHLA0/ ABUQ24GGLA0)
(ABUQ18GL2A0/ ABUQ21GL2A0/ ABUQ24GL3A0)

U-V

1.040(at25℃)

V-W

1.040(at25℃)

W-U

1.040(at25℃)

AUUQ36GH1 
(ATUQ36GMLE3)
(AVUQ36GKLA0)
(ABUQ36GGLA0)

U-V

0.628(at 25˚C)

V-W

0.628(at 25˚C)

W-U

0.628(at 25˚C)

AUUQ42GH1/ AUUQ48GH1/ AUUQ54GH1
(ATUQ42GMLE3/ ATUQ48GMLE3/ ATUQ54GMLE3)
(AVUQ42GLLA0/ AVUQ48GLLA0/ AVUQ54GLLA0)
(ABUQ42GRLA0/ ABUQ48GRLA0/ ABUQ54GRLA0)

U-V

0.438(at 25˚C)

V-W

0.438(at 25˚C)

W-U

0.438(at 25˚C)

1. Remove the connectors to the PCB.

2. Measure the resistance between the lines of each terminal of the com-

pressor. (Refer to Table 1)

3. Measure the resistance between the each terminal and the

chassis(pipe) of the compressor. (Refer to Table 2)

4. If the measurements are distinctively different from Table 1 and 2, the

compressor is decided to be burned.

Model

Resistance(

Ω

) at 20°C

Terminal

Inverter comp.

AUUQ18GH1 /AUUQ21GH1/ AUUQ24GH1
(ATUQ18GPLE3/ ATUQ21GPLE3/ ATUQ24GNLE3)
(AVUQ18GJLA0/ AVUQ21GJLA0 / AVUQ24GJLA0)
(ABUQ18GHLA0/ ABUQ21GHLA0/ ABUQ24GGLA0)
(ABUQ18GL2A0/ ABUQ21GL2A0/ ABUQ24GL3A0)

U-GND

1M

Ω

↑

V-GND

1M

Ω

↑

W-GND

1M

Ω

↑

AUUQ36GH1
(ATUQ36GMLE3)
(AVUQ36GKLA0)
(ABUQ36GGLA0)

U-GND

2M

Ω

V-GND

2M

Ω

W-GND

2M

Ω

AUUQ42GH1/ AUUQ48GH1/ AUUQ54GH1
(ATUQ42GMLE3/ ATUQ48GMLE3/ ATUQ54GMLE3)
(AVUQ42GLLA0/ AVUQ48GLLA0/ AVUQ54GLLA0)
(ABUQ42GRLA0/ ABUQ48GRLA0/ ABUQ54GRLA0)

U-GND

2M

Ω

V-GND

2M

Ω

W-GND

2M

Ω

• Verifying compressor burn

Содержание ABNQ18GHLA0





































































































Отзывы:

Нет отзывов