LG 49XS4F Скачать руководство пользователя страница 101

Страница: 101 / 125

INSTALLATION MENU

NOTE

•

Some features described in the Installation manual may not be supported in certain models.

Signage Setup

Use this menu to configure the digital signage after installation.

Power On Status

•

You can select the operating status of the monitor when the main power is switched on.

•

You can select from among PWR, STD, and LST.

•

PWR sets the status of the monitor to on whenever the main power is switched on.

•

STD sets the status of the monitor to standby when the main power is switched on.

•

LST sets the status of the monitor back to its previous status.

Wake On LAN

•

You can set whether to use the Wake On LAN feature.

•

You can set the feature to On or Off for each wired/wireless network.

•

Wired: When set to On, the Wake On LAN feature is enabled, letting you turn the product on remotely through the

wired network.

•

Wireless: When set to On, the Wake On LAN feature is enabled, letting you turn the product on remotely through the

wireless network.

LAN Daisy Chain

•

LAN Daisy Chain forms a daisy chain of LAN ports so that even if you connect only one monitor set to a network, the

other sets in the daisy are connected to the network.

•

The first set in the daisy chain must be connected to a network through a port that is not being used for the daisy

chain.

ENGLISH

Содержание 49XS4F






























































































































Результаты поиска

Содержание 49XS4F

Отзывы:

Похожие инструкции для 49XS4F

Бренды по названию

Популярные бренды

LG 49XS4F, Руководство пользователя

Результаты поиска

Содержание 49XS4F

Отзывы:

Похожие инструкции для 49XS4F

Бренды по названию

Популярные бренды