LG 43UV770M Скачать руководство пользователя страница 95

Страница: 95 / 123

206-4324

Reference: UV770M Hospital Operations

Hospital Features

The following table identifies when and how the UV770M hospital features are supported in three different

TV configurations.

As indicated in the introduction to this document, LG commercial TV functionality is based

on “ownership” of the Channel Map. For the purposes of this table, “CPU” indicates that the TV is in Pass-

through Mode with the Channel Map in the CPU (i.e., auto-tuned/edited channel lineup) and “PTC” indicates

that the TV is in Pass-through Mode with the Channel Map in the PTC (PTC-CTV Mode).

CPU

PTC

FTG/PPV Mode

Hospital Mode State

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Installer Menu

Item

IR Banks Enable

012

Scan Mode

013

Start Channel in Scan Mode

014

Feature Level

020

Bed 1/Bed 2

020

Multi-code IR

020

Speaker

020

Function Preview

025

Hospital Mode

027

Bed 1/Bed 2

027

Pillow Speaker Voltage

027

(b)

Speaker

027

Quick Shutoff

077

(c)

Channel Banks
Number of Banks Enabled

Channel Preview/Banks Setup Menu

Blanked Channel

Inactive TV

SAP Key (special use in Channel

Preview/Banks Setup Menu)

Aux Input Sources
Input List Menu

Aux in Channel Lineup

(d)

X*/(d)

TV Setup Menus
Sound Out (TV Speaker)

(e)

General (Standby Light)

Applicable for FTG Mode via CPU only.

X = feature supported
a) Turn ON function only. Always goes to channel 2-0.

b) Zenith pillow speaker code/(+12v) supply voltage. (When Installer Menu item 027 is set to 254 [factory default value], there

is no power [voltage] supplied to the pillow speaker interface.)

c) Quick Shutoff feature only functions when Scan Mode is enabled and if you are using an analog pillow speaker.

d) Dependent upon installer-defined FTG/PPV Channel Map.

e) Sound Out Menu is only accessible when the speaker selected is TV Only or both TV & Pillow.

Содержание 43UV770M




























































































































Результаты поиска

Содержание 43UV770M

Отзывы:

Бренды по названию

Популярные бренды

LG 43UV770M, Руководство по настройке коммерческого режима

Результаты поиска

Содержание 43UV770M

Отзывы:

Бренды по названию

Популярные бренды