LG 43UV770M Скачать руководство пользователя

Страница: 92 / 123

206-4324

Reference: FTG Mode via EBL (Local Configuration) (Cont.)

(Continued from previous page)

5. “Write” the FTG Channel Map to the EBL (switches the EBL from Pass-through Mode to FTG Mode).

Note:

After a “Write” of new data, the TV will briefly display a green text banner that shows the EBL

firmware version and release date.

6. “Read” the current FTG Installer Menu settings from the EBL using the FTG Installer Menu

Configur

ation Utility. If necessary to make changes to Installer Menu items, “Write” them back to the

EBL in FTG Mode.

Note:

When you “Read” the settings from the EBL, a pop-up notice will be displayed (see example

below) to indicate that the chassis ID of this model is unknown and so a generic Installer Menu profile

will be loaded. Click

to dismiss the pop-up window and continue. The resulting “generic” profile

contains all Installer Menu items, including a number of items that may not be applicable for this model.

Refer to the Installer Menu section of this document for detailed information on Installer Menu items

that are specfic to the UV770M, and make any changes necessary.

7. Save the FTG Channel Map and FTG Installer Menu settings to an FTG Configuration (.rml) file for

future use.

8. Tune the TV to a logical channel in the FTG Channel Map.

Содержание 43UV770M




























































































































Результаты поиска

Содержание 43UV770M

Отзывы:

Похожие инструкции для 43UV770M

Бренды по названию

Популярные бренды

LG 43UV770M, Руководство по настройке коммерческого режима

Результаты поиска

Содержание 43UV770M

Отзывы:

Похожие инструкции для 43UV770M

Бренды по названию

Популярные бренды