51
206-4324
053 - DIS. CH-TIME (Disable Channel-Time Display)
Set to 1 to disable the TV’s native Channel-Time display when a
custom channel label/channel information will be provided by the
MPI command. Set to 0 to enable the TV’s native Channel-Time
display.
069 - EN. CH-T COL. (Enable Display Characters Custom Color)
Set to 1 to enable custom color for MPI display characters. Set to
0 to disable custom color for MPI display characters.
070 - FOR. CH-TIME (Display Characters Foreground Color)
Set the foreground color for MPI display characters according to
the following color chart:
0 = Black
2 = Green
4 = Red
6 = Yellow
1 = Blue
3 = Cyan
5 = Violet
7 = White
If the foreground and background colors for the display characters
are the same, the background will be transparent.
Note:
This item and item 071 BCK. CH-TIME also apply to the
“Channel Not Available” message if item 073 CH NOT AVBLE is
set to 1 (enabled).
Note:
Items 070 FOR. CH-TIME and 071 BCK. CH-TIME are only
available in the Installer Menu when item 069 EN. CH-T COL. is
set to 1.
071 - BCK. CH-TIME (Display Characters Background Color)
See description for item 070 FOR. CH-TIME above. The color
chart is the same for both items.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CH. OVERIDE is set to 0, a “CHANNEL
NOT AVAILABLE” message is displayed when a user attempts to
direct tune a channel that is not included in the channel lineup.
Note:
This item is not available in the Installer Menu when item
028 CH. OVERIDE is set to 1.
Note:
This item is only applicable when the TV is in PTC-CTV
Mode.
075 - REVERT CH (Revert to Start Channel)
If set to 1 and loss of MPI communication occurs, TV automatically
tunes to the specified Start Channel.
Note:
This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 255.
077 - QUICK SHUTOFF
Allows end user (patient) to turn OFF TV using mechanical (analog)
Pillow Speaker Channel Up/Down buttons. Patient needs to press
and hold either channel button for time determined by value set.
Set to 0 to disable. Set from 1 to 17 to establish required hold
time of button—from 2 seconds to 10 seconds in half-second
increments.
Note:
This item is not available in the Installer Menu when item
013 SCAN MODE is set to 0.
078 - UPN MSB (UPN Most Significant Byte)
User programmable number, most significant byte readable by
MPI command. Note: Not linked to serial number.
079 - UPN MSB-1 (UPN Most Significant Byte-1)
User programmable number, most significant byte-1 readable by
MPI command. Note: Not linked to serial number.
080 - UPN MSB-2 (UPN Most Significant Byte-2)
User programmable number, most significant byte-2 readable by
MPI command. Note: Not linked to serial number.
081 - UPN LSB (UPN Least Significant Byte)
User programmable number, least significant byte readable by
MPI command. Note: Not linked to serial number.
082 - CHKSM ERROR (Checksum Error)
Enforces rigid MPI checksum validation. Set to 1 for validation.
Set to 0 to disable (does not check checksum on MPI async port).
SPI is always checked.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is 64 msec,
thus relaxing MPI timing requirements to be compatible with PC-
based Windows controlled systems. Range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time].)
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be permanent
by disabling the blocking hours function. Set to 1 to install Parental
Control restrictions permanently. Set to 0 for user-specified hours
control of blocking schemes.
Note:
This item is not available in the Installer Menu when item
021 V-CHIP is set to 0.
086 - V. MUTE TIME (Video Mute Time)
Use to extend the normal video mute time during channel change.
For example, you may wish to extend the normal video mute time
to prevent the display of encrypted video (i.e., from a Pro:Idiom
encrypted channel) that has not yet been decrypted. When set to
0, the normal video mute time is not extended. Set from 1 to 50 to
increase the normal video mute time in 100 ms step increments up
to a maximum of 5 seconds (e.g., the value of 25 represents 2.5
seconds, or 25 x 100 ms = 2.5 seconds).
088 - EN NOISE MUTE (Enable Noise Mute)
Applicable for analog channels only. If set to 1, audio mutes if no
signal is present.
090 - KEY LOCK
If set to 1, Key Lock is enabled, which means that the display
panel power button function will be locked, i.e., non-functional. Set
to 0 to disable Key Lock. Note that all IR features remain functional
regardless of this setting.
Installer Menu (Cont.)
