LG-Ericsson ipldk-60 Скачать руководство пользователя страница 302

Страница: 302 / 512

ipLDK-60

Issue 2.0

Admin Programming Manual

July, 2010

3.2.3

Station Attributes II (PGM 112)

PGM 112 is one of four (4) program groups that assign general attributes to the station range. Also, see PGMs 111, 113, and 114.

Procedure:

1. Press

the

[TRANS/PGM]

button.

2. Dial

112.

3. Enter the appropriate Station Range.

4. Select the desired Flexible button from the chart below.

5. Enter the appropriate value.

6. Press

the

[Hold/Save]

button.

PGM

112

Flex

Btn

Description

Default

Values

CO Warning

Tone

When enabled (On), the station user will receive a warning tone indicating the call

duration exceeds the CO Warning Tone time (PGM 180, Flexible button 22). The

tone is repeated at intervals of the CO Warning tone time.

0 (Off)

0 = Off

1 = On

Automatic Hold

When enabled (On), pressing a CO line button while on a CO line call places the

active CO line on hold and accesses the selected CO line.

1 (On) for Atd

0 (Off) for others

0 = Off

1 = On

CO Call Time

Restriction

If this parameter is enabled (On), an outgoing CO line call will disconnect when the

Call Cut -Off Timer (PGM113, Flexible button 12) expires.

0 (Off)

0 = Off

1 = On

Individual CO

Line Access

If enabled, the station user can access a specific CO line by dialing the individual CO

access code. See also PGM 107, Flexible button 8.

1 (Enable)

0 = Disable

1 = Enable

CO Line Queuing

When enabled (On), a station user can queue for a CO line if the user receives busy

tone when attempting to access the CO line.

1 (Enable)

0 = Disable

1 = Enable

CO PGM

If enabled (On), the station user can configure Flexible buttons to access a CO line

or CO line Group.

0 (Disable)

0 = Disable

1 = Enable

Содержание ipldk-60

































































































































































































































































































































































































































































































































Результаты поиска

Содержание ipldk-60

Отзывы:

Похожие инструкции для ipldk-60

Бренды по названию

Популярные бренды

LG-Ericsson ipldk-60, Описание функций и руководство по эксплуатации

Результаты поиска

Содержание ipldk-60

Отзывы:

Похожие инструкции для ipldk-60

Бренды по названию

Популярные бренды