LG-Ericsson ipldk-60 Скачать руководство пользователя страница 278

Страница: 278 / 512

ipLDK-60

Issue 2.0

Admin Programming Manual

July, 2010

At this point, the DKT is in the Program mode and can access the

various PGMs and parameters. Specific instructions for each

parameter are provided in the Admin Procedures given in section 3.

To access a specific PGM while in the Program mode,

1. Press

the

[TRANS/PGM]

button

2. Dial the 3-digit PGM code.

2.2.2

Navigation and Buttons

While in the Program mode, the [Volume Up/Down] can be used for

navigation through the PGM sections. Other buttons on the DKT also

provide special functions during Admin Programming. The BACK

softkey or [CONF] button, if assigned, move back one-step in the

process. The DELETE softkey or the [SPEED] button deletes the

current entry. The SAVE softkey or the

[Hold/Save]

button store an

entry to the system database. A value must be saved with the SAVE

softkey or

[Hold/Save]

button prior to moving to another parameter.

2.2.3

Entering and Saving Data

In most cases, after selecting a PGM, a specific parameter is selected

using a Flexible button and a value entered with the dial pad. When a

value is saved, the system will verify the value is in range and does not

conflict with other parameter settings. If the data value is valid,

confirmation tone is received. If the value is not valid, error tone is

received and a valid value can be entered without further action.

In some cases, after selecting a PGM, the Flexible buttons are used to

toggle a parameter value. In this case, the value is not checked since

the Flexible button only toggles the value ‘On’ or ‘Off’.

In certain PGMs e.g., a Station, CO line PGM group, the desired

station or CO line range is required. Once the parameter is selected,

the LCD will indicate the parameter value for the first station or CO line

in the range. Entering a single station or CO line number for both the

upper and lower end of the range will change the parameter for the

station or CO line number entered.

2.2.4

Resetting the System

When certain parameter values are changed, the system must be

reset to reorganize memory. Parameters that require a reset after

being changed include:

PGM 100 - Location,

PGM 101 – Board Assignment

PGM 103 – Logical Slot Assignment

PGM 108 – IP Settings

PGM 380 – VOIB Slot Assignment, RSG/IP Phone

PGM 381 – RSG/IP Phone Ports Assignment

Содержание ipldk-60

































































































































































































































































































































































































































































































































Результаты поиска

Содержание ipldk-60

Отзывы:

Похожие инструкции для ipldk-60

Бренды по названию

Популярные бренды

LG-Ericsson ipldk-60, Описание функций и руководство по эксплуатации

Результаты поиска

Содержание ipldk-60

Отзывы:

Похожие инструкции для ipldk-60

Бренды по названию

Популярные бренды