73725-B1
English User Manual
READ ENTIRE MANUAL BEFORE OPERATION to ensure proper use and care of your new Lezyne LED light. Traffic laws manda�ng
ligh�ng vary from country to country. Inform yourself about ligh�ng laws and regula�ons in the country of use.
Lezyne LED lights
do not conform to the German road traffic regula�on StVZO.
Technical Data
Output
Wa
�
age
Input voltage
Illuminant
Power cable length
500 Lu
m
en
7.5 W
12-
48V
AC
DC
(E-bike ba�ery systems)
2 LED
130 c
m
Technical Data
Output
Wa
�
age
Input voltage
Illuminant
Power cable length
800 Lu
m
en
8 W
12-
48V
AC
DC
(E-bike ba�ery systems)
2 LED
130 c
m
Motors Compatibility
MICRO DRIVE 500 HV
LITE PRO DRIVE 800 SWITCH HV
Warnings
The light technical equipment must be safely installed during the en�re usage and must be ensured that the light will not be
moved in its posi�on due to uninten�onal adjustment.
DO NOT LOOK DIRECTLY INTO LIGHT BEAM or shine into eyes of another.
Lezyne LED Lights have a water resistance ra�ng of IPX7 under IEC standard 60529. Submerging the device is not recommend
-
ed. If moisture does enter the casing, air out un�l completely dry.
DO NOT ATTEMPT TO REMOVE ELECTRONICS. Doing so will void warranty.
Lezyne USA, Inc. does not accept any liability for injuries or other damages resul�ng from the improper use or improper
installa�on of this product in any circumstance.
Warranty
In U.S. and U.K., Lezyne LED Lights carry a two (2) year warranty from the original purchase date to the original owner (proof
of purchase required). Lezyne warran�es cover any manufacturing defects in materials or workmanship. Issues not covered by
warranty include normal wear & tear, improper installa�on, a�emp�ng to access or modify electronics, damage or failure due
to accident, misuse, abuse and/or neglect.
For all warranty issues worldwide, please contact the retailer that sold the product.
In the case of an LED not working properly or not working at all do not use your light anymore. These lights must be replaced
immediately.
For any warranty ques�ons contact:
Installation
Lezyne recommends that our E-Bike lights be installed by an E-bike professional. Below is general informa�on about wiring and
moun�ng the light to a compa�ble bike.
Black
− Nega�ve
Yellow
+
Posi�ve
Mounting
The light must be mounted in a height between 250 mm and 1200 mm. It must be ensured that the light technical equipment
will not be covered by any parts of the bike (�re, etc…).
Operation
The front light will be controlled via the on board electronics of the E-bike system. These lights are only to be mounted on
E-Bikes with DC voltage that have their own ba�ery charge indica�on and control. The e-bike system must be capable of
automa�cally shu�ng the light off when the onboard ba�ery reaches a cri�cal voltage to avoid deep dischaging of the
ba�ery.
Our e-bike lights are powered by the e-bike system and need to be manually installed. Proper installa�on may require some
disassembly of the bike and motor (depending on make and model/ba�ery type) and addi�onal wiring to connect the light to the
e-bike. Please contact the e-bike or motor manufacturer for installa�on instruc�ons. Please note: Any disassembly may void the
warranty of your e-bike. It is highly recommended to have a trained e-bike professional install your lights for you. Below is general
informa�on about electrical connec�vity.
Powered by
E-bike Ba�ery
Powered by
E-bike Ba�ery
Hold 2 sec. On/Off
Mode Control Bu�on
The LITE PRO DRIVE 800 SWITCH HIGH VOLT is designed
to work with a wide variety of E-Bike systems. It is
intended as an solu�on to add powerful headlight to an
E-bike system. It supports power supplies and ba�eries
from
12-48V
. It requires a minimum of
8W
to func�on
properly and includes a Handle Bar Switch to power the
light on/off and change modes. Please contact the bicycle
manufacturer or supplier for informa�on on compa�bility
and installa�on.
Motors Compatibility
The MICRO DRIVE 500 HIGH VOLT is designed to work
with a wide variety of E-Bike systems. It is intended as an
solu�on to add powerful headlight to an E-bike system. It
supports power supplies and ba�eries from
12-48V
. It
requires a minimum of
7.5W
to func�on properly and
includes a Handle Bar Switch to power the light on/off and
change modes. Please contact the bicycle manufacturer
or supplier for informa�on on compa�bility and
installa�on.
o-ring
HANDLEBAR
▼
Wire Fork Mount / Universal Aluminum Mount
Between
250 mm
and
1200 mm
Floor
▼
Direct X-lock Stem Mount
Between
250 mm
and
1200 mm
Floor
BLAST
800
LUMENS
ENDURO
400
LUMENS
ECONOMY
150
LUMENS
FLASH 1
300
LUMENS
700
LUMENS
FLASH 2
