background image

Dismantling the vehicle 

 

The following 2 pages contain general instructions for use when working on an HS250h.    Read 

these instructions before proceeding to the HV battery removal instructions on page 18.     

 

WARNING:

 

・ 

The high voltage system may remain powered for up to 10 

minutes after the vehicle is shut off or disabled.    To prevent 

serious injury or death from severe burns or electric shock, avoid 

touching, cutting, or opening any orange high voltage power 

cable or any high voltage component.     

 

1.  Shut off the ignition (

READY

 indicator is 

off).    Then disconnect the cable from the 

auxiliary battery negative (-) terminal.     

 

 

 

 

2.  Remove the service plug grip.     

(1) 

Disengage the 2 clips and 2 guides, and remove the battery service hole cover.

     

Caution:  

 

Wear insulated gloves for the following 3 steps.   

 

(2)  Slide the handle of the service plug grip to the left.     

(3)  Raise the release handle of the service plug grip.     

(4)  Remove the service plug grip.     

(1)

2

 

3

 

4

 

(5)  Apply insulating tape to the socket of the service plug grip to insulate it.     

 

15

Содержание HS 250h



































Отзывы: