Scanner manual registration
This item is used to manually register the flatbed and ADF on the MFP scanner unit. Registration should be performed
whenever the ADF unit, flatbed unit, or controller card are replaced.
To manually register a Duplex ADF, perform the following steps:
1
In the Configuration Menu, scroll to the Scanner Manual Registration menu item.
2
Select
Scanner Manual Registration
.
3
Select
Print Quick Test Page
.
4
To view and adjust the duplex ADF front side registration, place the quick test page faceup into the ADF.
5
Select
Copy Quick Test
.
6
After the quick test page copies, select
ADF Front
.
7
Use the plus to increase or the minus to decrease the settings value for horizontal adjust and top margin.
Note:
Each button press moves the margin values one pixel in the respective direction.
8
Select
Submit
to accept the value.
9
Save changes by placing the print quick test page face up and selecting
Copy Quick Test
.
10
Repeat steps 6, 7, and 8 as needed.
11
To view and adjust the duplex ADF backside registration, place the quick test page face down up into the ADF, and
select
Copy Quick Test
.
12
After the quick test page copies, select
ADF Back
.
13
Use the plus or minus to increase or decrease the settings value for horizontal adjust and top margin.
Note:
Each button press moves the margin values one pixel in the respective direction.
14
Select
Submit
to accept the value.
15
Verify the changes by placing the print quick test page face down and selecting
Copy Quick Test
.
16
Repeat steps 13, 14, and 15 as needed.
To manually register the flatbed, perform the following steps:
1
In the Configuration Menu, select the Scanner Manual Registration menu item.
2
Select the Print Quick Test Page menu item.
3
To view and adjust the flatbed registration, place the quick test page into the flatbed.
4
Select the Copy Quick Test Page item.
5
After the quick test page copies, select
Flatbed
.
6
Use the plus or minus to increase or decrease the settings value for the left or top margin.
Note:
Each button press moves the margin values one pixel in the respective direction.
7
Select
Submit
to accept the value.
8
Place the print quick test page on the flatbed and select
Copy Quick Test
.
7527
Service menus
222
Содержание XC2132
