Lexmark X734DE Скачать руководство пользователя | Manualshive

Страница: 238 / 626

background image

3-42

Service Manual

7526

Go Back

Previous

Next

Motor Calibration

This setting synchronizes the aligner and fuser motor speeds with the transfer belt speed to ensure that the
output is printed correctly.

Note:

This test should be run at 600 dpi resolution and with duplex disabled.

To run the Motor Calibration:

1.

Touch

Motor Calibration

in the Config Menu.

2.

Touch

Motor Calibration

.

Calibrating…

displays, and then the multiple function printer feeds eight blank pages.

Touch

Back

to return to the Configuration main menu.

Paper Prompts

Controls the source the printer selects for a change paper source message. The printer displays the change
paper source message based on the size of the paper requested and not by the paper type.

Selections include

Auto

,

Multi-Purpose Feeder

, and

Manual Paper

. The multipurpose feeder is available on

some printer models.

Note:

If the Configure MP setting is changed to Manual, a power-on reset is performed, and then the value of

the Paper Prompts menu item before the power-on reset was MP Feeder, then when the printer restarts, the
printer automatically changes the Paper Prompts setting to Manual Paper.

Load Manual overrides that would result in a change paper message are disabled for

Paper

or

Env

prompts that

are set to Manual, Manual Paper, or Manual Env.

To change the settings for Paper Prompts:

1.

Touch

Paper Prompts

in the Config Menu.

2.

Touch the left or right arrow to toggle between

Auto

,

Multi-Purpose Feeder

, and

Manual Paper

.

3.

Touch

Submit

.

Submitting changes…

is displayed.

You are automatically returned to the Configuration main menu.

Envelope Prompts

Controls the source the printer selects for a change envelope source message. The printer displays the change
envelope message based on the size of the envelope requested and not by the envelope type.

Selections include Auto, MP Feeder, and Manual Env. MP Feeder is only available on some printer models.

Note:

If the Configure MP setting is changed to Manual, and a power-on reset is performed, and the value of

the Env Prompts menu item before the power-on reset was MP Feeder, then when the printer restarts, the
printer automatically changes the Env Prompt setting to Manual Env.

Load Manual overrides that would result in a change paper message are disabled for Paper or Env prompts that
are set to Manual, Manual Paper, or Manual Env.

«
...
236
237
238
239
240
...
»

Содержание X734DE



















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X734DE

Бренд: QMS Страницы: 2

Бренд: Xerox Страницы: 14

Бренд: Ricoh Страницы: 126

Бренд: U-Line Страницы: 33

Бренд: Oki Страницы: 20

LaserPro StellarMark IFII Series

Бренд: GCC Technologies Страницы: 111

DocuCentre-VI C2264

Бренд: Fuji Xerox Страницы: 129

Бренд: Riso Страницы: 82

Бренд: Copystar Страницы: 1

Бренд: Wang Страницы: 39

Бренд: Infotec Страницы: 72

Бренд: Ioline Страницы: 78

CRYSTAL 650 - NETWORK

Бренд: Philips Страницы: 84

AGEP50 - COLOR VIDEO PRINTER

Бренд: Panasonic Страницы: 40

208D - AR B/W Laser

Бренд: Sharp Страницы: 2

208D - AR B/W Laser

Бренд: Sharp Страницы: 4

Бренд: Sharp Страницы: 37

1451 - AL B/W Laser

Бренд: Sharp Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды