manualshive.com logo in svg

Lexmark X734DE, Руководство по обслуживанию

Поделиться
Скачать
Lexmark X734DE Скачать руководство пользователя страница 227

Diagnostic aids

3-31

  

7526

Go Back

Previous

Next

Reset Fuser Count

Resets the fuser count value to zero. The Event Log records each time that a user executes the Reset Fuser 
Count operation. See 

“Event Log” on page 3-33

 for more information. This setting only appears if the 

Maintenance Warning and Intervention function is enabled in the printer Configuration ID.

To reset the fuser count:

1.

Touch 

Reset Fuser Counter 

from the Config Menu.

2.

Touch 

Reset Fuser Counter

 again.l

You are returned to the Config Menu.

USB Scan to Local

This setting allows you to limit or expand the uses for the USB device on the front of the multiple function printer. 
If you select 

On

 (the default), the contents of the USB device can be viewed or saved on another device, such 

as an USB-connected computer. If you select 

Off

, only the MFP can view the USB device contents.

To change the setting:

1.

Touch 

USB Scan to Local 

from the Config Menu.

2.

Touch the left or right arrows to select either 

Off

 or 

On

.

3.

Touch 

Submit

.

Touch 

Back

 to return to the Config Menu screen.

Require Standby

See 

“Require Standby” on page 3-46

.

LES Applications

See 

“LES Applications” on page 3-46

.

Key Repeat Initial Delay

See 

“Key Repeat Initial Delay” on page 3-46

.

Key Repeat Rate

See 

“Key Repeat Rate” on page 3-46

.

Clear Custom Status

See 

“Pel Blurring” on page 3-47

.

Pel Blurring

See 

“Pel Blurring” on page 3-47

.

USB Speed

See 

“USB Speed” on page 3-47

.

Exit Config Menu

This selection exits Configuration Menu, and then 

Resetting the 

Printer

 displays. The printer performs a POR and returns to normal 

mode.

Reset Fuser Counter

Reset Fuser Counter

Содержание X734DE



















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды