Lexmark X734DE Скачать руководство пользователя страница 197 | Manualshive

Страница: 197 / 626

Lexmark X734DE Скачать руководство пользователя страница 197

Diagnostic aids

3-1

7526

Go Back

Previous

Next

3. Diagnostic aids

This chapter explains the tests and procedures to identify printer failures and verify repairs have corrected the
problem.

Accessing test and diagnostic procedure menus

There are different test and diagnostic menus that can be accessed during POR to identify problems with the
multiple function printer. Turn off the MFP and turn it back on while holding particular keys. You may also have
to satisfy any security protocols that system administrators may have been placed on these menus.

Diagnostics menu

1. Turn off the multifunction printer.
2. Press and hold

3

and

6

.

3. Turn on the MFP.
4. Release the buttons when the progress bar

displays.

The Diagnostics menu group

contains the settings and

operations used while

manufacturing and servicing the

printer.
See

“Diagnostics menu” on

for more information.

Configuration menu

1. Turn off the multifunction printer.
2. Press and hold

2

and

6

.

3. Turn on the MFP.
4. Release the buttons when the progress bar

displays.

The Configuration menu group

contains a set of menus, settings,

and operations which are

infrequently required by a user.

Generally, the options made

available in this menu group are

used to configure a printer for

operation.
See

“Configuration menu

(CONFIG MENU)” on page 3-30

for more information.

Start the

multifunction printer

without initializing

the scanner.

1. Turn off the multifunction printer.
2. Press and hold

3

and

7

.

3. Turn on the MFP printer.
4. Release the buttons when the progress bar

displays.

«
...
195
196
197
198
199
...
»

Содержание X734DE



















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды