Lexmark X734DE Скачать руководство пользователя страница 191

Страница: 191 / 626

Diagnostic information

2-153

7526

Go Back

Print quality—blank page

Step

Questions / actions

Yes

Is all the packing material for the

photoconductor unit in question removed?

Go to step 2.

Remove the packing

material.

Replace the photoconductor unit for the color

in question.
Does this fix the problem?

Problem resolved.

Go to step 3.

Enter the Diagnostics mode (turn off the

printer, press and hold

and

, turn on the

printer, and release the buttons when the

clock graphic displays). Perform the

appropriate cartridge drive motor test for the

missing color. See

“General motor tests

procedures” on page 3-12

Did the motor run?

Go to step 5.

Replace the EP drive

assembly. See

“Electrophotographic
(EP) drive assembly
removal” on page 4-89

Check the high voltage contact from the

HVPS to the photoconductor charge roll.

Ensure the contact springs are properly

mounted and that the charge roll contact

spring is making good contact with the HVPS

spring that runs through the left printer frame.

Are the spring(s) defective?

Replace the transfer

contact assembly.

Go to step 6.

High voltage

contact path

High voltage

power supply

Содержание X734DE



















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X734DE

Отзывы:

Бренды по названию

Популярные бренды

Lexmark X734DE, Руководство по обслуживанию

Результаты поиска

Содержание X734DE

Отзывы:

Бренды по названию

Популярные бренды