Lexmark X734DE страница 151 Скачать руководство пользователя

Страница: 151 / 626

Diagnostic information

2-113

7526

Go Back

920.10—POST—Three toner sensors not connected error service check

Step

Questions / actions

Yes

Remove the left cover. See

“Left cover

removal” on page 4-23

. Check all toner level

sensor cables (A) connected to the rear of the

HVPS.

Are any of the cables damaged?

If one or two of the toner

level sensor are damaged:

• Disconnect the

sensor(s), and

• Go to step 2.

If two toner level sensors

are damaged, replace the

damaged sensor. See

“Toner level sensor
removal” on page 4-174

Go to step 2.

Disconnect one of the toner level sensors,

and POR the MFP. See

“Toner level sensor

removal” on page 4-174

Does the 910.10 error occur again?

Then this is one of the

three bad toner level

sensors. Continue

disconnecting the toner

level sensors until three

sensors are disconnected

and the 920.10 error

occurs.
Replace the toner level

sensors that are

disconnected. See

“Toner

level sensor removal” on
page 4-174

Repeat this step for the

other toner level sensors

until the 920.10 error

occurs.

Содержание X734DE



















































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X734DE

Отзывы:

Похожие инструкции для X734DE

Бренды по названию

Популярные бренды

Lexmark X734DE, Руководство по обслуживанию

Результаты поиска

Содержание X734DE

Отзывы:

Похожие инструкции для X734DE

Бренды по названию

Популярные бренды