Lexmark 4500-00 Series Скачать руководство пользователя

Страница: 169 / 246

Diagnostic aids

3-33

4500–E320/E322

USB NPA mode

USB NPA mode allows for two way communication between the host
computer and the printer.

Perform the following steps to change the USB NPA setting:

1. Enter the configuration mode. See

“Configuration mode” on

page 3-14

for more information.

2. Perform a double button press nine times. This moves to the

USB NPA mode item on the configuration menu. The USB NPA
(Error) light is blinking.

3. The current USB NPA setting is indicated by the off/on/auto

(Press Button) light.

•

When the light is off, the USB port does not search for NPA
data within the received data.

•

When the light is blinking, the USB port searches for optional
NPA data within the received data.

•

When the light is on solid, the USB port requires that data
sent to the printer be in NPA format.

4. Perform a brief button press to select a different USB NPA

setting.

5. Perform a long button press. All lights blink once, indicating the

setting is saved.

6. Exit the configuration mode by turning the printer power off.

Off/on/auto Setting

value

❍

USB port does not search for NPA data within the
received data.

●

USB port requires that data sent to the printer be in NPA
format.

✳

USB port searches for optional NPA data within the
received data.

Содержание 4500-00 Series























































































































































































































































Результаты поиска

Содержание 4500-00 Series

Отзывы:

Похожие инструкции для 4500-00 Series

Бренды по названию

Популярные бренды

Lexmark 4500-00 Series, Руководство по обслуживанию

Результаты поиска

Содержание 4500-00 Series

Отзывы:

Похожие инструкции для 4500-00 Series

Бренды по названию

Популярные бренды