Lexmark 4500-00 Series Скачать руководство пользователя | Manualshive

Страница: 161 / 246

background image

Diagnostic aids

3-25

4500–E320/E322

Parallel protocol

The printer supports two parallel protocol settings: standard and
fastbytes. When the protocol is set to standard, information is
received at a normal transmission rate. When the protocol is set to
fastbytes, information is received at a much faster transmission rate
provided the host computer supports the fastbytes mode.

Perform the following steps to change the parallel protocol setting:

1. Enter the configuration mode. See

“Configuration mode” on

for more information.

2. Perform a double button press two times. This moves to the

parallel protocol item on the configuration menu. The parallel
protocol (Load Paper) light comes on solid.

3. The current parallel protocol setting is indicated by the

off/on/auto (Press Button) light. When the light is off, the parallel
protocol is set to standard. When the light is on, the parallel
protocol is set to fastbytes. Perform a brief button press to select
the parallel protocol setting.

4. Perform a long button press. All lights blink once, indicating the

setting is saved.

5. Exit the configuration mode by turning the printer power off.

Off/on/auto Setting

value

❍

Parallel port uses Standard protocol.

●

Parallel port uses Fastbytes protocol.

«
...
159
160
161
162
163
...
»

Содержание 4500-00 Series























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4500-00 Series

KXPX2M - HOME PHOTO PRINTER

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 9

Jetwriter KX-CL500

Бренд: Panasonic Страницы: 32

Бренд: Canon Страницы: 36

Бренд: Canon Страницы: 62

WorkCentre 4260S

Бренд: Xerox Страницы: 8

Бренд: Canon Страницы: 738

Бренд: Samsung Страницы: 143

imageRUNNER 6570

Бренд: Canon Страницы: 274

Бренд: Xerox Страницы: 14

Бренд: Xerox Страницы: 2

Бренд: Make Mendel Страницы: 29

mobile pro advance

Бренд: AM TECH Страницы: 16

Бренд: SAGEMCOM Страницы: 146

Бренд: Intuitive Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды