Lexmark 4500-00 Series Скачать руководство пользователя

Страница: 120 / 246

2-90

Service Manual

4500

Poor fusing of image

Light print

FRU

Action

Fuser lamp

The fuser may not be operating at
the proper temperature to fuse the
toner to the paper. See

“Hot fuser

service check ” on page 2-76

Paper (not a FRU)

Make sure recommended paper is
being used.

FRU

Action

Toner cartridge (not a FRU)

Make sure the toner cartridge is
installed correctly and is not low on
toner.

If the problem continues, install a
new toner cartridge.

Transfer roll
HVPS contact (transfer roll)
HVPS board

Check the transfer roll for signs of
toner buildup and contamination.

Inspect the HVPS contact (transfer
roll) for contamination.

Inspect the HVPS board for
contamination where it meets the
HVPS contacts.

If all components appear free of
contamination, replace the following
FRUs one at a time in the order
shown:

• Transfer roll
• HVPS contact (transfer roll)
• HVPS board

Содержание 4500-00 Series























































































































































































































































Результаты поиска

Содержание 4500-00 Series

Отзывы:

Похожие инструкции для 4500-00 Series

Бренды по названию

Популярные бренды

Lexmark 4500-00 Series, Руководство по обслуживанию

Результаты поиска

Содержание 4500-00 Series

Отзывы:

Похожие инструкции для 4500-00 Series

Бренды по названию

Популярные бренды