manualshive.com logo in svg

Lexmark 4227-100, Руководство по обслуживанию

Поделиться
Скачать
Lexmark 4227-100 Скачать руководство пользователя страница 75

Repair Information 4-14

4227-100

Carrier Plate Removal 

1. Remove the top cover.

See 

“Top Cover Removal” on page 4-37

.

2. Remove the print unit.

3. Remove the carrier.

4. Remove the lower pinch roller.

5. Remove the carrier motor.

6. Remove the auto gap motor and its bracket.

7. Remove the carrier motor bracket.

8. Remove the right side frame.

9. Remove the two screws holding the carrier plate to the left side 

frame, and remove the carrier plate.

Label Jam Removal

When a pressure-sensitive label separates from its protective 
backing and jams and sticks to the paper separator below the carrier 
plate, the following procedure should be used to remove the label.

1. Remove the top cover.

See 

“Top Cover Removal” on page 4-37

.

2. Remove the tractor assembly. 

3. Remove the print unit.

See 

“Print Unit Removal” on page 4-28

.

4. Remove the paper separator.

See 

“Paper Separator Removal” on page 4-26

.

5. Carefully remove the label from the paper separator. If the label 

is jammed below the carrier plate or on the lower portion of the 
paper guide/platen assembly, carefully remove the label without 
scratching either surface.

Содержание 4227-100







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды