Lexmark 4227-100 Скачать руководство пользователя страница 70

Страница: 70 / 134

4-9

4227-100

Belt Tension Pulley Plate Assembly Removal

1. Remove the top cover.

See

“Top Cover Removal” on page 4-37

2. Turn the printer so you are facing the rear of the printer.

3. Remove both tension pulley plate mounting screws [1].

4. Manipulate the left side of the tension spring off the lug.

5. Slide the pulley plate to the right and off the carrier plate.

6. Slide the pin out of the pulley and manipulate the belt out of the

tension pulley plate.

Bottom Cover Removal

1. Remove the tractor assembly.

See

“Right Side Frame Removal” on page 4-34

2. Remove the top cover.

See

“Top Cover Removal” on page 4-37

3. Remove the print unit.

4. Remove the power supply.

5. Remove the main logic board.

6. Remove the tractor cable and bracket.

7. If replacing the bottom cover, write the machine serial number

and part number on the blank label.

Содержание 4227-100







































































































































Результаты поиска

Содержание 4227-100

Отзывы:

Бренды по названию

Популярные бренды

Lexmark 4227-100, Руководство по обслуживанию

Результаты поиска

Содержание 4227-100

Отзывы:

Бренды по названию

Популярные бренды