Lexmark 4227-100 Скачать руководство пользователя страница 116

Страница: 116 / 134

6-1

4227-100

6. Preventive Maintenance

This chapter describes procedures for printer preventive
maintenance. Following these recommendations can help prevent
problems and maintain optimum performance.

Lubrication

Warning: Petroleum-based lubricants can attack polycarbonate
parts causing premature failure. Use only mineral oil-based
lubricant.

The following parts should be lubricated when replaced:

•

Oil felt (carrier block)

•

Tractor unit

•

Side frame (left)

•

Side frame (right)

•

Pinch roller (lower)

•

Pinch roller spring (left)

•

Pinch roller spring (center)

•

Pinch roller spring (right)

•

Paper separator

Specified Lubricants

•

Oil - P/N 1280443

•

Approved equivalents:

– Mobil DTE27

– Shell Tellus 100

– Fuchs Renolin MR30

•

Grease - P/N 6934659

•

Approved equivalent:

– Mobil 28

Содержание 4227-100







































































































































Результаты поиска

Содержание 4227-100

Отзывы:

Бренды по названию

Популярные бренды

Lexmark 4227-100, Руководство по обслуживанию

Результаты поиска

Содержание 4227-100

Отзывы:

Бренды по названию

Популярные бренды