Levo Combi Скачать руководство пользователя страница 15

Страница: 15 / 63

7.2

Delivery

Because of the complex nature of this wheelchair it will be delivered and demonstrated

to you by your local agent.

The wheelchair comprises the following components:

Component

Number

Wheelchair base

Seat unit

Backrest unit

Knee support

Chest strap

Footrest

Set of batteries

Joystick unit

Battery charger

Accessories as on delivery note

Corresponding

order

form

7.3

Storage

The ideal condition to store the

LEVO

combi

is a temperature between – 40° and + 60°

Celsius (between -30° and +140° Fahrenheit). The humidity should not be above 90%.

Please take care to guarantee these mentioned conditions to provide a long life time for
the

LEVO

combi.

Accessories

There are many kinds of suitable accessories to the

LEVO

combi

. A list of accessories is

available from your local agent.

Warning

For your own safety you should read and carefully follow all instructions in the

manual.

Before using the

LEVO

combi

, have your

LEVO

dealer explain the instructions to

you. It also helps if you have a friend to listen as well. Study the instruction

manual yourself or if you cannot understand it, get a friend to help you doing so.
Don’t hesitate to ask for any explanation.

The

LEVO

combi

is designed for outdoor and indoor use. In principle it is not

recommended to drive on uneven, soft or steeply sloping ground. Using the

LEVO

combi

outdoors switch on the lights at dawn and dusk and in the dark of

course.

Avoid driving through puddles. The wheelchair and especially electrical

components are very sensitive to too much water even some splashes of water

Содержание Combi
































































Результаты поиска

Содержание Combi

Отзывы:

Похожие инструкции для Combi

Бренды по названию

Популярные бренды

Levo Combi, Инструкция по эксплуатации

Результаты поиска

Содержание Combi

Отзывы:

Похожие инструкции для Combi

Бренды по названию

Популярные бренды