background image

 

 

User Manual for LCO-i100 Console 

www.levitronix.com 

 

PL-4066-00, Rev03, DCO# 21-230 

 

19

 

 

9.2  Symbols and Signal Words 

 

Symbol / 

Signal Word 

Description 

Type 

Source 

DANGER 

Indication of an imminently hazardous situation that, if not 
avoided, will result in death or severe injury. Limited to the 
most extreme situation 

Signal word 

SEMI S1-0701 

WARNING 

Indication of a potentially hazardous situation which, if not 
avoided, could result in death or severe injury. 

Signal word 

SEMI S1-0701 

CAUTION 

Indication of potentially hazardous situations which, if not 
avoided, could result in moderate or minor injury. Also alert 
against unsafe practice. 

Without safety alert indication of hazardous situation which, 
if not avoided, could result in property damage. 

Signal word 

SEMI S1-0701 

 

 

Safety alert for “Warning” and “Caution” 

Safety alert 

SEMI S1-0701 

 

 

Safety alert for “Danger” 

Safety alert 

SEMI S1-0701 

 

Caution (refer to accompanying documents) 
(is used on article labels for reference to manual) 

Refer to manual 

ISO 3864 

 

General warning 

Hazard identification 

ISO 3864 

 

Toxic material, poison 

Hazard identification 

IEC 61310 

 

Corrosive material, corrosion 

Hazard identification 

IEC 61310 

 

Cut/sever hand, sharp object 

Hazard identification 

ANSI Z535.3 

 

Strong magnetic field 

Hazard identification 

SEMI S1-0701 

 

Danger: electricity, electrical hazard 

Hazard identification 

IEC 61310, 

ISO 3864 

 

Wear safety gloves 

Hazard avoidance 

Mandatory action 

IEC 61310 

 

Unplug power line 

Hazard avoidance 

Mandatory action 

SEMI S1-0701 

 

Do not touch 

Hazard avoidance 

Prohibition 

ANSI Z535.4 

ISO 3864

 

 

No pacemakers 

Hazard avoidance 

Prohibition 

SEMI S1-0701 

Table 12: Safety symbols and signal words 

Содержание PuraLev LCO-i100




















Отзывы: