Levitronix PLD-iF30SU.1 Скачать руководство пользователя страница 25

Страница: 25 / 39

User Manual for PuraLev

iF30SU

www.levitronix.com

PL-4078-00, Rev00, DCO# 20-228

4.3 Electrical Installation of OEM Model

4.3.1 Overview Wire Designation of Driver Cable

Wire
Name

Wire

Color

Description

Standard
Designation

Typical Levels

Note

P+

red

+ 24 VDC

Supply

Voltage: 24 VDC ±10%
Power: 35 W

P- to be connected to earth.

P-

black

Power Input
Ground / Earth

Ain1

violet

Analog Input 1

(Current Input)

Reference Value
(Set Flow or
Speed)

4..20 mA = 0..100% of full scale flow

4..20 mA = 0..16000 rpm

Speed limit = 13000 rpm
Cutt-off speed = 0 rpm

For Flow Control mode (default mode).

For Speed Control Mode.

450 Ohm shunt input, no galvanic isolation.
The designation of the analog inputs can be changed
with

Levitronix

Service Software.

Ain2

grey-
pink

Analog Input 2

(Voltage Input)

Configurable as
setpoint input

0..10 V

Analog voltage input: 0

– 10V

(7.9 kOhm, no galvanic isolation).

Note: Max. input voltage of 11 V shall not be
exceeded.

The designation of the analog inputs can be changed
with

Levitronix

Service Software.

Ain_GND blue

Analog Input
Ground

Reference for analog inputs Ain1 and Ain2.

Din1

pink

Digital Input 1

Enable Flow
Control Mode
(Reset)

5-24 V



Flow control active

0 V



Flow control not active

Galvanic separation with optocoupler and
2.2 k



input resistance.

The “

Enable

” signal switches the system on and off.

Resets pump from error state with 300-700ms pulse.

Din2

grey

Digital Input 2

Zero Adjust

Edge triggered: 0 V

5-24 V

Galvanic separation with optocoupler and
2.2 k



input resistance.

Triggers a Zero Adjust of the flow sensor.

Din_COM yellow

Common
Digital Input

Aout1

blue-
red

Analog Output

(Voltage Output)

Actual Flow
Value

0..10 V = 0..100% of full scale

Direct connection, no protection. Galvanic isolation on
user side is required. GND is reference.

The configuration of the analog output can be changed
with

Levitronix

Service Software

Dout1

brown

Digital Output 1

Status Pump

Closed circuit



active, pump running

Open circuit



not active, system off or error

Open drain, max. 24V, 100mA

This signal indicates the state of the system. If not
active, pump is either in “Off” or in “Error” state.

The configuration of the digital outputs can be
changed with

Levitronix

Service Software.

Dout2

white

Digital Output 2

Status
Flow Sensor

Closed circuit



active, measurement o.k.

Open circuit



not active, measure. error

Slow blinking (2 Hz)



Zero Adjust error

Fast blinking (10 Hz)



Zero Ad. in progress

Open drain, max. 24V, 100mA

The configuration of the digital outputs can be changed
with

Levitronix

Service Software.

GND

white-
green

Analog Ground

Reference for Aout1, Dout1 and Dout2

RS485+

brown-
green

RS485 +

Fieldbus

Modbus RTU protocol

Termination resistors recommended

RS485-

white-
yellow

RS485 -

Shield

shield
wire

Shielding

Shielding

To be connected to earth
(see wire P-, black)

Table 15: Signals of the driver cable with designation for standard firmware

Note 1: For other configurations of PLC Inputs and Outputs refer to relevant firmware documentation
Note 2: Configurations can be done with Levitronix

Service Software

Note 3: Power wires (P+, P-) have cross section 1.5 mm

and all others 0.14 mm

Содержание PLD-iF30SU.1








































Результаты поиска

Содержание PLD-iF30SU.1

Отзывы:

Бренды по названию

Популярные бренды

Levitronix PLD-iF30SU.1, Руководство пользователя

Результаты поиска

Содержание PLD-iF30SU.1

Отзывы:

Бренды по названию

Популярные бренды