3-Wire Relay Receiver
Cat. Nos. WSP05-010, WSP05-020, WSP05-080, WST05-010, WST05-020 & WST05-080
International versions available
INSTALLATION
PROGRAMMING:
The receiver must be powered when programming. After programming, settings are retained when power is disconnected. The
receiver sensitivity is reduced when in Learn Mode to prevent unintentionally associating unwanted transmitters with the receiver.
Transmitters should be within 15 feet (5 meters) of the receiver when programming. Program the receiver in any of the modes
below.
Rocker Mode (default):
In Rocker Mode the receiver responds only on a transmitter press and not on the release. For example,
one side of the rocker on a wireless light switch will activate the relay (turn the light ON) when pressed and the opposite side of the
same rocker will deactivate the relay (turn the light OFF) when pressed.
Momentary Mode:
In Momentary Mode, each end of the rocker on a wireless light switch acts as a separate button. Each end of
the rocker programs separately to 1 or more receivers. When a rocker is pressed the output on the receiver will activate (turning the
electrical load ON). When the rocker is released the output will deactivate (turning the electrical load OFF).
Toggle Mode:
In Toggle Mode, each end of the rocker acts as a separate button. Each end of the rocker programs separately.
When the rocker is pressed the output of the receiver will always change state (if OFF, it will turn ON; if ON, it will turn OFF). Like
Rocker Mode, the output status only changes when a button is pressed and is ignored on the release.
Follow the instructions below for the desired programming mode:
Rocker Mode (default) Programming Instructions
1.
Read all Rocker Mode programming steps before taking any action to program receiver in Rocker Mode.
2.
Activate Rocker Learn Mode by pressing and holding the LRN button for 1 second
(See Figure A)
. The electrical load
connected to the receiver will begin turning ON and OFF in a slow pattern.
3.
When associating a wireless light switch with the receiver, press one end of a switch rocker
(See Figure B)
. When associating
a transmitter other than a wireless light switch, press the LRN or TCH button on the transmitter
(see appropriate transmitter
starter guide)
. The load will stay ON for about 3 seconds indicating that the receiver has stored the transmitter’s unique ID in its
memory.
4. NOTE:
If only one transmitter is desired then skip Step 4 and exit Learn Mode by following Step 5. To associate a second
transmitter with this receiver, wait until toggling of the load resumes. Repeat the instructions in Steps 3 and 4 until the unique
IDs of all desired transmitters (up to 30) are stored in the memory of the receiver.
5.
To complete programming, just wait; the receiver automatically exits Learn Mode after 30 seconds. Alternatively, press and hold
the LRN button for 2 seconds to exit Learn Mode.
Momentary Mode Programming Instructions
1.
Read all Rocker Mode programming steps before taking any action to program receiver in Momentary Mode.
2.
While the receiver is in Rocker Learn Mode, press and hold the LRN button for 3 seconds
(See Figure A)
. The electrical load
connected to the receiver will begin turning ON and OFF in a fast pattern. The receiver is now in Momentary Learn Mode.
3.
Follow steps 3-5 of
"Rocker Mode Programming Instructions."
Toggle Mode Programming Instructions
1.
Read all Rocker and Momentary Mode programming steps before taking any action to program receiver in Toggle Mode.
2.
While the receiver is in Momentary Learn Mode, press and hold the LRN button for 3 seconds
(See Figure A)
. The electrical
load connected to the receiver will continue turning ON and OFF in a fast pattern. The receiver is now in Toggle Learn Mode.
3.
Follow steps 3-5 of
"Rocker Mode Programming Instructions."
Selective Deleting:
Follow the Program Mode steps above to delete a transmitter from a receiver’s memory. Upon pressing the
LRN button on a transmitter
(See Rocker Mode Programming Instructions, Step 3)
which has previously been associated with
the receiver, the electrical load connected to the receiver will stay OFF for 3 seconds indicating that the receiver has removed the
transmitter’s unique ID from its memory.
Clear All:
If the CLR button is pressed and held for 2 seconds
(See Figure C)
, the entire memory of the receiver will be deleted.
The receiver will instantly enter the default programming mode (Rocker Mode) indicated by the electrical load turning ON and OFF.
WARNINGS AND CAUTIONS:
• TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS.
• IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT AN ELECTRICIAN.
• RELAY RECEIVERS ARE INTENDED ONLY FOR USE INDOORS, IN DRY LOCATIONS, AND WITH PERMANANTLY INSTALLED
FIXTURES.
• SUITABLE FOR USE ON A CIRCUIT CAPABLE OF DELIVERING NOT MORE THAN 15 RMS SYMMETRICAL AMPERES MAXIMUM.
• RELAY RECEIVERS SHOULD NOT BE INSTALLED IN A LOCATION WHERE THE UNIT WILL BE IN CLOSE PROXIMITY TO THE
LIGHT BULB(S) OR OTHER SOURCES OF HEAT, PARTICULARLY WITH HIGHER WATTAGE LOADS. INSTALLATION IN CLOSE
PROXIMITY TO LIGHT BULBS OR OTHER HEAT SOURCES MAY SUBJECT THE RECEIVER TO TEMPERATURES EXCEEDING
THE OPERATING TEMPERATURE RATING
(SEE SPECIFICATIONS TABLE)
.
DESCRIPTION:
The 3-Wire Relay Receiver provides fast and simple installation of remote controls for lighting and other loads. The receiver responds to
radio signals from self-powered wireless light switches and other compatible transmitters. The receiver mounts in ceiling junction boxes,
wall switch boxes, and wiring cavities. The threaded version mounts through standard 1/2" knock-out holes
(See Figure E)
.
COMPATIBLE DEVICES:
• Single Rocker Self-powered Wireless Light Switch
• Dual Rocker Self-powered Wireless Light Switch
• Handheld Self-powered Wireless Light Switch
• Key Card Access Switch
• SLT Wireless Sensor
• Self-powered Wireless Occupancy Sensor
• More transmitters available
TOOLS NEEDED FOR INSTALLATION:
• Non-conductive probe (pencil or ballpoint pen) • Electrical tape
• Wire nuts
• Screwdriver
TO INSTALL:
The 3-Wire Relay Receiver provides fast and simple installation of remote controls for lighting and other loads. The receiver responds to
radio signals from self-powered wireless light switches and other compatible transmitters. The receiver mounts in ceiling junction boxes,
wall switch boxes, and wiring cavities.
Single Pole or Multi-way Wireless Switch (1 or more wireless light switches)
1.
Read the
WARNINGS AND CAUTIONS
section before beginning these installation options. Read all steps for this option before
taking any action to install receiver.
2.
WARNING:
To avoid risk of fire, shock, or death,
TURN OFF POWER
at circuit breaker or fuse and verify that it is OFF before
installation begins. Make sure that it remains OFF until installation is complete. Please be aware that with some versions of the
product, it is possible to have multiple branch circuits feeding the Relay Receiver.
3.
For in-wall installation, a wiring box must be used. For ceiling installation make wire connections inside a junction box.
Ensure that
the temperature in the ceiling box will not exceed 50 degrees C (see specifications)
. For best wireless signal performance
install receiver in plastic box away from floor and away from metal objects.
4.
Connect wires as shown in
Figure D
. Twist wire nuts on clockwise making sure no bare wires show. Wrap connections with
electrical tape.
5.
Restore power and follow programming instructions for appropriate programming mode
(see “Programming” below)
. For this
installation, Rocker Mode (the default programming mode) is recommended.
6.
Test receiver. (If receiver is not working, review wiring and programming instructions or see
“Troubleshooting”
in product manual.)
7.
Stow all wires in wiring box. Finish any installation of fixture or wall switch.
DI-000-WST05-00A
