DESCRIPTION
The Leviton Outdoor video monitoring camera uses a single Cat 5e cable to distribute both power and video between the camera and Leviton Structured Media™ Center.
INSTALLATION
Install with a single gang exterior water-proof junction box for new construction and retrofit installations at each of the camera locations. Some installations may require a
water-proof surface mount box if installing to an exterior wall, trim, or soffet.
NOTE:
When installed in indoor applications, use a low voltage mounting ring.
WIRING
To prewire for the Outdoor Camera, simply run a single Cat 5e UTP cable from the SMC to each camera location desired.
NOTE:
If your cable run length exceeds 100 meters (328 ft) you will need to
power your camera locally. Install a two conductor (minimum 18-2) cable with
your Cat 5e to locally power the camera. Also, see "
Powering Locally"
in the
POWERING YOuR CAmERA
section.
INSTALLING THE OuTDOOR CAmERA:
•
Strip back your Cat 5e cable and terminate to camera using one of the
following methods:
a)
Terminate the camera Cat 5e cable directly onto the camera board
using the 110 IDC termination block provided. Fan out your Cat 5e
cable and follow the color code indicated in
Figure 2
. Punch down your
Cat 5e cable using a 110 punch tool.
b)
Terminate a
Cat 5e jack 5G108-R*5 (sold separately)
to your cable
(use T568A color codes - Figure 3)
, then use a short Cat 5e patch
cord from the jack to the RJ-45 on the camera board to complete the
connection
(Figure 4)
.
•
Set Dip Switch to termination method used
(Figure 1)
:
a)
IDC (Leviton recommended)
b)
RJ-45
c)
LOCAL
NOTE:
Local is used if you are powering your camera locally
(refer to Powering Locally)
.
•
Mount the camera onto the box securing the mounting plate with
gasket to the gang box
(if mounting in harsh weather exposed to
wind and rain take caution to ensure the camera is sealed water tight into the box)
.
NOTE:
If mounting the outdoor camera to a wall use the threaded mounting hole on
the bottom of the camera back side. If mounting camera to a ceiling or a soffet, simply
rotate the camera on the ball and socket joint to avoid an inverted image. Alternatively, in
extreme situations, use the threaded mounting hole on the top, back side of the camera.
•
To adjust the camera viewing angle loosen twist knob on the mounting bracket, adjust
the camera angle and tighten the twist knob.
POWERING YOuR CAmERA:
Powering Remotely with Camera Hub (Cat. No. VSHuB):
If your camera Cat 5e cable is 100 Meters (328ft) or less, your camera can be
powered over the Cat 5e from the Camera Hub located inside your Structured
Media System. A power jack on the Camera Hub requires 12VDC power from
either the power supply provided with the Camera Hub board or one of the power
supplies listed below:
Leviton Compatible Power Supplies:
NOTE:
Each Outdoor Camera in no light conditions draws about 220 mA from the
Camera Hub. Each Indoor Camera draws about 110 mA from the Camera Hub.
Make sure the sum of the currents from all devices powered by the
power supply in the SMC does not exceed the maximum output of
that power supply.
• 47605-PSA (Maximum output: 12V DC at 3000 mA)
• 47605-PSB (Maximum output: 12V DC at 750 mA)
• 48212-DC (Maximum output: 12V DC at 1500 mA)
Outdoor Camera
Installation Instructions
DI-000-VSOUT-00A
VSOUT
59-25 Little Neck Parkway.
Little Neck, N.Y. 11362-2591, uSA
Tech Support: 800-824-3005
www.leviton.com
Figure 4
LE
D
BL
OR
BR
GR
Cat # VSIND/VSOUT
Assembled in Mexico
www.leviton.com
RCA
IDC
local
RJ45
Camera Board
RJ45 Jack
inserts here
Cat 5e
Patch Cord
Cat 5e Jack
5G108-R*5
(to Voice and Data Board)
Twist knob
Package Contents:
Camera Unit (1)
Power Supply AC Adapter (1)
Power Adapter (1) with screws
LED
BL
OR
BR
GR
IN
OUT
Cat # VSIND/VSOU
T
Assembled in Mexico
www
.leviton.com
RCA
loca
l
RJ-45
IDC
RJ45
Power/Video
LED
BL
OR
BR
GR
IN
OUT
Cat # VSIND/VSOU
T
Assembled in Mexico
www
.leviton.com
RCA
IDC
local
RJ45
IDC
Power/Video
LED
BL
OR
BR
GR
IN
OUT
Cat # VSIND/VSOU
T
Assembled in Mexico
www
.leviton.com
RCA
local
RJ45
IDC
Local Power
Video over
IDC/RJ45
RJ45 jack
inserts here
a)
b)
*
Recommended for Outdoor Camera
c)
Figure 1 – Dip Switch Settings
White/Blue 5
White/Orange 3
Green 2
PIN #
White/Green 1
PIN #
6 Orange
4 Blue
7 White/Brown
8 Brown
Figure 3
White/Green
Green
White/Orange
Orange
Blue
White/Blue
White/Brown
Brown
Figure 2
