Leuze 50116368 страница 53 Скачать руководство пользователя

Страница: 53 / 116

Installation and mounting

Leuze electronic GmbH + Co. KG

BCL 308

Installation and mounting

6.1

Storage, transportation

Unpacking



Check the packaging content for any damage. If damage is found, notify the post office or shipping

agent as well as the supplier.



Check the delivery contents using your order and the delivery papers:

• Delivered quantity

• Device type and model as indicated on the name plate

• Brief manual

The name plate provides information as to what BCL type your device is. For specific information, please

refer to Chapter 5.
Name plates of the bar code readers of the BCL 308

series

Figure 6.1: Device name plate BCL 308



Save the original packaging for later storage or shipping.

If you have any questions concerning your shipment, please contact your supplier or your local Leuze

sales office.



Observe the applicable local regulations when disposing of the packaging materials.

6.2

Mounting the BCL 308

The BCL 308

bar code readers can be mounted in different ways:

• Via four or six M4x5 screws on the device bottom.
• Via a BT 56/BT 59 mounting device in the two fastening grooves on the device bottom.

ATTENTION!

Package the device for transport and storage in such a way that is protected against shock and

humidity. Optimum protection is achieved when using the original packaging. Ensure compliance

with the approved environmental conditions listed in the specifications.

NOTE

All BCL 308

are delivered with a protective cover on the connection side which must be removed

before attaching a connection hood.

ATTENTION!

The BCL 308

does not fulfill degree of protection IP 65 until the connection hood has been

screwed on. Minimum tightening torque of the housing connecting screw of the connection hood

is 1.4 Nm!

Содержание 50116368





















































































































Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды

Leuze 50116368, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание 50116368

Отзывы:

Похожие инструкции для 50116368

Бренды по названию

Популярные бренды