Leuze electronic MSI-MD-FBX Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 47

Leuze electronic MSI-MD-FBX Скачать руководство пользователя страница 30

Starting up the device - Configuration

Leuze electronic

MSI-MD-FBX

30

8

Starting up the device - Configuration

8.1

Overview

The function of the muting controller is set via two DIP switch blocks, each of which has eight switches. The
DIP switch blocks are located behind a cover in the housing of the muting controller and are not accessible
in normal operation.

NOTICE

This muting controller can only be operated in operating mode 7 (see chapter 8.2 "Setting the
operating mode").

Parameter

You can set the following parameters for the function of the muting controller:

DIP switch

Function

Settings

1

Number of the muting sensors

2-sensor muting

4-sensor muting (not permissible)

2

Muting mode

Timing controlled muting

Sequence controlled muting (not permissible)

3

EDM

With EDM

Without EDM

4

Restart

Automatically via machine interface signal

Manually via acknowledgment unit

5

Muting-enable

With muting-enable

Without muting-enable

6

Muting timeout

With muting-timeout extension

Without muting-timeout extension

Procedure

Ä

Disconnect the muting controller from voltage.

Ä

Remove the cover from the housing of the muting controller (four screws; Operational controls).

Ä

Set the operating mode of the muting controller via the DIP switch blocks (see chapter 8.2 "Setting the
operating mode").

Ä

Remount the cover on the housing on the muting controller.

ð

Tighten the screws with a torque wrench. Torque: 0.6 … 0.8 Nm

Ä

Connect the muting controller to the voltage supply

Ä

Restart the muting controller.

ð

After the device is started, the 7-segment display shows the set operating mode.

NOTICE

Error when configuring the muting controller in process mode!

If the switch position of the DIP switch blocks is changed in process mode, an error is triggered
and the OSSDs switch off.

Ä

Only set the configuration of the muting controller while the device is in a voltage-free state.

«
...
28
29
30
31
32
...
»

Содержание MSI-MD-FBX
















































Отзывы:

Нет отзывов