Leuze electronic LSIS 222 Скачать руководство пользователя страница 77

Страница: 77 / 95

Configuration using configuration codes

Leuze electronic

Technical description LSIS 22x

TNT

35/7-2

7.6.4

Reset to factory settings

By reading in the following service code, the LSIS 22x is reset to factory settings.

Attention!

When resetting to factory settings, the entire configuration of the LSIS 22x is lost and
all parameters are reset to their standard values.

Figure 7.50: Service code for resetting to factory settings

Listed in the following are the most important factory settings according to device model:

Factory settings LSIS 222 M5M-R1 - RS 232 interface

• Baud rate

9600bit/s

• Data format

data bits,

parity,

stop bit

• Framing

<STX>

DATA

• No read character

’

• Manual trigger mode

start command:

stop command:

Factory settings LSIS 223 M5M-R1 - USB interface

• USB operating mode

USB keyboard emulation

• Keyboard layout

GERMAN

• Framing

’

ENTER

’

• No read character

none

• Streaming presentation mode

Reset to factory settings

Содержание LSIS 222
































































































Результаты поиска

Содержание LSIS 222

Отзывы:

Leuze electronic LSIS 222, Техническое описание, Страница: 77 / 95

Результаты поиска

Содержание LSIS 222

Отзывы: